Alcatel-Lucent 060321-10, Rev. B Скачать руководство пользователя страница 250

Страница: 250 / 2354

show spantree mode

Distributed Spanning Tree Commands

page 5-108

OmniSwitch CLI Reference Guide

March 2011

show spantree mode

Displays the current global Spanning Tree mode parameter values for the switch.

show spantree mode

Syntax Definition

Defaults

Platforms Supported

OmniSwitch 10K

Usage Guidelines

The global parameters for spanning tree can be activated or configured using the related commands.

Examples

-> show spantree mode

Spanning Tree Global Parameters

Current Running Mode : Per VLAN,

Current Protocol : N/A (Per VLAN),

Path Cost Mode : 32 BIT,

Auto Vlan Containment : N/A

Cisco PVST+ mode : Disabled

Vlan Consistency check : Disabled

output definitions

Current Running Mode

The spantree mode active on the switch. (

Flat

Per VLAN

)

Current Protocol

The spantree protocol active on the switch.

Path Cost Mode

The path cost mode value configured on the switch. (

AUTO

32 BIT

)

Auto Vlan Containment

The Auto VLAN containment mode configured on the switch
(

Enabled

Disabled

Cisco PVST+ mode

The PVST+ mode configured on the switch (

Enabled

Disabled

Vlan Consistency check

Specifies if VLAN consistency check is

Enabled

Disabled

on the

switch.

Содержание 060321-10, Rev. B



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды

Alcatel-Lucent 060321-10, Rev. B, Справочное руководство CLI

Результаты поиска

Содержание 060321-10, Rev. B

Отзывы:

Похожие инструкции для 060321-10, Rev. B

Бренды по названию

Популярные бренды