Alcatel-Lucent 060321-10, Rev. B Скачать руководство пользователя страница 344 | Manualshive

Страница: 344 / 2354

background image

multi-chassis vip-vlan

Multi-Chassis Commands

page 7-20

OmniSwitch CLI Reference Guide

March 2011

multi-chassis vip-vlan

Creates a virtual IP VLAN, which is a special type of VLAN used to provide the underlying LAN infra-
structure for the support of basic IP/Layer 3 services on a multi-chassis link aggregation group.

multi-chassis vip-vlan vlan

no multi-chassis vip-vlan vlan

Syntax Definitions

vlan

VLAN to be created as a virtual IP VLAN within the range [1 - 4094].

Defaults

NA

Platforms Supported

OmniSwitch 10K

Usage Guidelines

•

This command can be executed only if a valid multi-chassis chassis identifier within the range [1 - 2] is
configured on the switch at that time.

•

The virtual IP VLANs are distinguished from the others by a distinct type of VLAN by using the
VLAN management show commands.

•

The only ports that can be configured as members of a virtual IP VLAN are the multi-chassis link
aggregates. In other words, ordinary aggregates or physical ports cannot be configured as members of
this type of VLAN.

•

As a result of the previous behavior, a standard IP interface cannot be configured on a non-VIP VLAN
if any of the members of such VLAN are a multi-chassis aggregate group. In terms of network topol-
ogy that basically means that a VLAN that performs IP routing cannot span several switches through-
out the entire network if any of its member ports is a multi-chassis aggregate. This aspect must be taken
into account while design the network topology and, especially, while migrating exsiting networks
towards a multi-chassis topology.

•

The IP interfaces configured on a virtual IP VLAN have limited functionality. Routing protocols and
VRRP cannot be configured on such IP interfaces.

•

IPv6 interfaces cannot be configured on a virtual IP VLAN in this release (7.1.1.R01).

•

IP interfaces configured on virtual IP VLANs have a special meaning and for each interface the user
must configure two distinct IP addresses. One of these addresses is called the management address and
it is used by each switch within a multi-chasiss system to provide management services. Each switch
has its own unique IP address. The other address is called vitual IP address and it will be used for
supporting routing of packets terminated on the multi-chassis switches. Unlike the management
address, the virtual IP address must be the same on the peer switches operating in multi-chassis mode.

«
...
342
343
344
345
346
...
»

Содержание 060321-10, Rev. B



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 060321-10, Rev. B

DGS-1024D - Switch

Бренд: D-Link Страницы: 16

DGS-1016D - Switch

Бренд: D-Link Страницы: 44

DES-6000 Series

Бренд: D-Link Страницы: 3

DES-5024 - Switch

Бренд: D-Link Страницы: 2

DES-3828 - xStack Switch - Stackable

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 192

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 110

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 4

DGS-105 - Switch

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды