e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
June 2004 © TOSHIBA TEC
2 - 66
Notes:
•
The digit after the hyphen in “Code” of the following table is a sub code.
•
In “RAM”, the NVRAM of the board in which the data of each code is stored is indicated. “M”
stands for the LGC board and “SYS” stands for the SYS board.
Adjustment mode (05) <e-STUDIO202L/232/282>
Code
Classi-
fication
Items
Func-
tion
Default
<Accept-
able
value>
RAM
Contents
Proce-
dure
200
Devel-
oper
Automatic adjustment of
auto-toner sensor
(Fuser heater ON)
ALL
-
-
As the value increases,
the sensor output
increases correspond-
ingly.
The value starts chang-
ing approx. 2 minutes
after this adjustment was
started and is automati-
cally set in the range of
2.35 to 2.45 V.
*
Selection is disable
when developer unit
is not installed.
(Chap. 3.1)
17
201
Devel-
oper
Correction of auto-toner
sensor
(Fuser heater ON)
ALL
164
<0-255>
M
Corrects the control
value of the auto-toner
sensor setup in 05-200.
*
Selection is disable
when developer unit
is not installed.
3
205
Devel-
oper
Developer bias DC output
adjustment
ALL
135
<0-255>
M
As the value increases,
the transformer output
increases correspond-
ingly. Remove the devel-
oper unit and install the
adjustment jig to make
adjustment.
(Chap. 3.6)
3
210
Charger
Main charger grid bias out-
put adjustment
ALL
90
<0-255>
M
3
220
Transfer
Transfer transformer DC
output adjustment (H)
ALL
165
<0-255>
M
3
221
Transfer
Transfer transformer DC
output adjustment (C)
ALL
179
<0-255>
M
3
222
Transfer
Transfer transformer DC
output adjustment (L)
ALL
126
<0-255>
M
3
233
Separa-
tion
Separation transformer DC
output adjustment (H)
ALL
64
<0-255>
M
3
234
Separa-
tion
Separation transformer DC
output adjustment (C)
ALL
65
<0-255>
M
3
235
Separa-
tion
Separation transformer DC
output adjustment (L)
ALL
46
<0-255>
M
3
280
Process
Forced performing of idling
for toner recycle
ALL
-
M
Perform this adjustment
before the replacement
of the developer mate-
rial. (The toner is forcibly
removed from the
cleaner.)
6
286
Laser
Laser power adjustment
ALL
63
<0-255>
M
When the value
increases, the laser out-
put increases corre-
spondingly.
3
305
Scanner
Image location adjustment
of secondary scanning
direction
(scanner section)
ALL
125
<92-164>
SYS
When the value
increases by “1”, the
image shifts by approx.
0.137 mm toward the
trailing edge of the
paper.
1
05/12
Summary of Contents for e-STUDIO200L
