Toshiba e-STUDIO200L, Service Manual

Page: 44 / 708

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 8
C940 Circuit related ser-
vice call Engine-CPU abnormality P. 5-76
C970 Process related
service call High-voltage transformer abnormality: Leakage of the
main charger is detected. P. 5-76
CA10 Laser optical unit
related service call Polygonal motor abnormality: The polygonal motor is not
rotating normally. P. 5-60
CA20 H-Sync detection error: H-Sync detection PC board can-
not detect laser beams. P. 5-60
CB10 Finisher related
service call Transport motor abnormality: The transport motor or
stack transport roller is not rotating normally. [MJ-1025] P. 5-61
CB20 Delivery motor abnormality: Delivery motor or delivery
roller is not rotating normally. [MJ-1022/1025] P. 5-62
CB30 Tray lift motor abnormality: The tray lift motor is not rotat-
ing normally or the delivery tray is not moving normally.
[MJ-1025] P. 5-63
CB50 Staple motor (staple/fold) abnormality: The staple motor
is not rotating normally or the stapler is not moving nor-
mally. [MJ-1025] P. 5-64
CB60 Stapler unit shift motor abnormality: The stapler unit shift
motor is not rotating normally or the Stapler Unit is not
moving normally. [MJ-1025] P. 5-66
CB80 Backup RAM data abnormality:
1) Abnormality of checksum value on finisher controller
board is detected when the power is turned on.
[MJ-1025]
2) Abnormality of checksum value on punch controller
board is detected when the power is turned on.
[MJ-1025 (when MJ-6005 is installed)]
P. 5-67
CC30 Stack processing motor abnormality: The stack process-
ing motor is not rotating normally or the stack delivery belt
is not moving normally. [MJ-1022]
Paddle motor abnormality: The paddle motor is not rotat-
ing normally or the swing guide is not moving normally.
[MJ-1025] P. 5-67
CC50 Horizontal registration motor abnormality: The horizontal
registration motor is not rotating normally or the puncher
is not moving normally.
[MJ-1025 (when MJ-6005 is installed)] P. 5-69
CC60 Punch motor abnormality: The punch motor is not rotating
normally or the puncher is not moving normally.
[MJ-1025 (when MJ-6005 is installed)] P. 5-69
CC80 Front jogging motor abnormality: Front jogging motor is
not rotating normally or the front alignment plate is not
moving normally. [MJ-1022]
Alignment motor (front) abnormality: The alignment motor
(front) is not rotating normally or the front alignment plate
is not moving normally. [MJ-1025] P. 5-70
CC90 Upper stack tray lift motor abnormality: The upper stack
tray lift motor is not rotating or the upper stack tray is not
moving normally. [MJ-1022] P. 5-71
CCA0 Lower stack tray lift motor abnormality: The lower stack
tray lift motor is not rotating or the lower stack tray is not
moving normally. [MJ-1022] P. 5-72
CCB0 Rear jogging motor abnormality: Rear jogging motor is
not rotating normally or the rear alignment plate is not
moving normally. [MJ-1022]
Alignment motor (rear) abnormality: The alignment motor
(rear) is not rotating normally or the rear alignment plate
is not moving normally. [MJ-1025] P. 5-73
Error code Classification Contents Troubleshooting