manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Service Manual

The Suzuki Grand Vitara JB416 is a versatile SUV known for its reliable performance and rugged design. Whether you need routine maintenance or more extensive repairs, our Service Manual is available for free download at manualshive.com. Keep your vehicle in top condition with our comprehensive manual.

Share
Download
background image

4F-51 Electronic Stability Program: 

3) Install console rear panel referring to “Console Box 

Components:  in Section 9H in related manual”.

4) Connect negative (–) cable to battery.

5) After completing installation, calibrate yaw rate / G 

sensor assembly referring to “Sensor Calibration: ”.

Yaw Rate / G Sensor Inspection

S5JB0E4606019

• Check sensor for dents, cracks or deformation.

• Check sensor connector (sensor side and harness 

side) and sensor connector lock mechanism for 
damage or crack.

• Check connector terminals for bend, corrosion or rust.
If it is found faulty, replace yaw rate / G sensor assembly.

Steering Angle Sensor On-Vehicle Inspection

S5JB0E4606020

CAUTION

!

 

Before each inspection, confirm steering 
angle sensor calibration is completed.
If calibration is incompleted, calibrate sensor 
referring to “Sensor Calibration: ”.

 

1) Connect SUZUKI scan tool to data link connector 

(DLC) (1) with ignition switch OFF.

Special tool
(A):  SUZUKI scan tool 

2) Turn ignition switch to ON position and select menu 

“DATA LIST” mode of SUZUKI scan tool.
Refer to scan tool operator's manual for further 
derails.

3) Check “Steering angle Sen” under “DATA LIST” of 

SUZUKI scan tool in the following steering wheel 
conditions.

• Front wheels in straight-ahead position

• Rotate steering wheel a round in clockwise 

(counter clockwise) from straight-ahead position

If steering angle condition is out of specification, 
replace steering angle sensor.

Steering angle Specification

Steering Angle Sensor Removal and Installation

S5JB0E4606021

Refer to “Steering Angle Sensor Removal and 
Installation:  in Section 6B”.

Steering Angle Sensor Inspection

S5JB0E4606022

• Check sensor for dents, cracks or deformation.

• Check sensor connector (sensor side and harness 

side) and sensor connector lock mechanism for 
damage or crack.

• Check connector terminals for bend, corrosion or rust.
If it is found faulty, replace steering angle sensor (1).

I6JB01460031-01

(A)

1

I5JB0A450008-01

Vehicle condition

Steering angle

Front wheels in straight-
ahead position

0 

±

 3

°

Rotate steering wheel a 
round in clockwise

360 

±

 3

°

Rotate steering wheel a 
round in counterclockwise

–360 

±

 3

°

I6JB01460032-01

1

I6JB01460033-01

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GRAND VITARA JB416

Jeep Commander Overview Manual preview
Commander
Brand: Jeep Pages: 25
Jeep Commander Warranty Information Booklet preview
Commander
Brand: Jeep Pages: 51
Farenheit CCD-5XS Owner'S Manual preview
CCD-5XS
Brand: Farenheit Pages: 8
Yakima K343 Manual preview
K343
Brand: Yakima Pages: 11
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Brand: GMC Pages: 20
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Brand: Lincoln Pages: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Brand: Volkswagen Pages: 26
Chevrolet Camaro 12000 1968 Series Factory Assembly Instruction Manual preview
Camaro 12000 1968 Series
Brand: Chevrolet Pages: 455
Toyota 4Runner 2019 Quick Reference Manual preview
4Runner 2019
Brand: Toyota Pages: 52
walser 30968 User Instructions preview
30968
Brand: walser Pages: 24
AutoLoc SB3PR Series User Manual And Installation Manual preview
SB3PR Series
Brand: AutoLoc Pages: 6
Ford Focus 2008 Quick Reference Manual preview
Focus 2008
Brand: Ford Pages: 2
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Brand: Acura Pages: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Brand: Ford Pages: 325
Opel 2011 Astra J Owner'S Manual preview
2011 Astra J
Brand: Opel Pages: 242
Buick 1997 Park Avenue Manual preview
1997 Park Avenue
Brand: Buick Pages: 420
Stack ROLL POD Installation Manual preview
ROLL POD
Brand: Stack Pages: 4
Blue Ox BX2711 Installation Instructions Manual preview
BX2711
Brand: Blue Ox Pages: 8

Brands by name

Popular brands

Load more brands