Suzuki GRAND VITARA JB416 Service Manual Download Page 195

Page: 195 / 474

Transfer: Non-Shift Type (Transfer without Shift Actuator) 3C-78

Repair Instructions

Transfer Oil Change

S5JB0E3326001

Refer to “Transfer Oil Change: Motor-Shift Type (Transfer with Shift Actuator)”.
The point which is different from the motor-shift type (transfer with shift actuator) is described.

Transfer oil capacity (Reference)
: 1.6 liters (3.4/2.8 US/lmp.pt)

Transfer Oil Level Check

S5JB0E3326002

Refer to “Transfer Oil Level Check: Motor-Shift Type (Transfer with Shift Actuator)”.

Transfer Oil Seal Removal and Installation

S5JB0E3326003

Refer to “Transfer Oil Seal Removal and Installation: Motor-Shift Type (Transfer with Shift Actuator)”.

Transfer Assembly Dismounting and Remounting

S5JB0E3326004

Refer to “Transfer Assembly Dismounting and Remounting: Motor-Shift Type (Transfer with Shift Actuator)”.

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Search results

Summary of Contents for GRAND VITARA JB416

Reviews:

Related manuals for GRAND VITARA JB416

Brands by name

Popular brands

Suzuki GRAND VITARA JB416, Service Manual

Search results

Summary of Contents for GRAND VITARA JB416

Reviews:

Related manuals for GRAND VITARA JB416

Brands by name

Popular brands