manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Service Manual

The Suzuki Grand Vitara JB416 is a versatile SUV known for its reliable performance and rugged design. Whether you need routine maintenance or more extensive repairs, our Service Manual is available for free download at manualshive.com. Keep your vehicle in top condition with our comprehensive manual.

Share
Download
background image

Table of Contents 5-iii

Gear Shift Lever Front Case Assembly 

Components.......................................................5B-*

Gear Shift Shaft and Fork Components ...............5B-*
Input Shaft Assembly, Output Shaft 

Assembly and Countershaft Assembly 
Components.......................................................5B-*

Manual Transmission Oil Change ........................5B-*
Transmission Shift Control Lever Removal 

and Installation ...................................................5B-*

Transmission Shift Control Lever Inspection........5B-*
Back Up Light Switch Removal and 

Installation ..........................................................5B-*

Back Up Light Switch Inspection..........................5B-*
Gear Shift Control Lever Rear Case 

Assembly Removal and Installation ...................5B-*

Gear Shift Control Lever Rear Case 

Assembly Disassembly and Reassembly ..........5B-*

Gear Shift Control Lever Rear Case 

Assembly Inspection ..........................................5B-*

Gear Shift Lever Front Case Assembly 

Removal and Installation....................................5B-*

Gear Shift Lever Front Case Assembly 

Disassembly and Reassembly ...........................5B-*

Gear Shift Lever Front Case Assembly 

Inspection...........................................................5B-*

Engine Rear Mounting Replacement ...................5B-*
Manual Transmission Assembly 

Dismounting and Remounting............................5B-*

Manual Transmission Unit Disassembly ..............5B-*
Manual Transmission Unit Reassembly...............5B-*
Locating Spring Inspection...................................5B-*
Input Shaft Disassembly ......................................5B-*
Input Shaft Inspection ..........................................5B-*
Input Shaft Reassembly .......................................5B-*
Countershaft Disassembly and Assembly............5B-*
Countershaft and Reverse Idle Gear 

Inspection...........................................................5B-*

Output Shaft Disassembly and Assembly ............5B-*
Output Shaft Inspection .......................................5B-*
Manual Transmission Front Case 

Disassembly and Assembly ...............................5B-*

Manual Transmission Adapter Case 

Disassembly and Assembly ...............................5B-*

Specifications ....................................................... 5B-*

Tightening Torque Specifications........................ 5B-*

Special Tools and Equipment ............................. 5B-*

Recommended Service Material ......................... 5B-*
Special Tool ........................................................ 5B-*

Clutch ........................................................5C-*

General Description ............................................. 5C-*

Clutch (Hydraulic Type) Construction ................. 5C-*

Component Location ........................................... 5C-*

Clutch Fluid Pipe and Hose Location .................. 5C-*

Diagnostic Information and Procedures ............ 5C-*

Clutch (Hydraulic Type) Symptom 

Diagnosis .......................................................... 5C-*

Clutch Pedal Height Inspection ........................... 5C-*
Clutch Pedal Free Travel Check ......................... 5C-*
Clutch Fluid Inspection........................................ 5C-*
Air Bleeding of Clutch System............................. 5C-*

Repair Instructions .............................................. 5C-*

Clutch Pedal Position (CPP) Switch 

Removal and Installation................................... 5C-*

Clutch Pedal Position (CPP) Switch 

Inspection and Adjustment................................ 5C-*

Clutch Fluid Pipe and Hose Removal and 

Installation ......................................................... 5C-*

Clutch Fluid Pipe and Hose Inspection ............... 5C-*
Clutch Master Cylinder Removal and 

Installation ......................................................... 5C-*

Clutch Master Cylinder Inspection ...................... 5C-*
Clutch Operating Cylinder Assembly 

Removal and Installation................................... 5C-*

Clutch Cover, Clutch Disc and Flywheel 

Components...................................................... 5C-*

Clutch Cover, Clutch Disc and Flywheel 

Removal and Installation................................... 5C-*

Clutch Cover, Clutch Disc and Flywheel 

Inspection.......................................................... 5C-*

Specifications ....................................................... 5C-*

Tightening Torque Specifications........................ 5C-*

Special Tools and Equipment ............................. 5C-*

Recommended Service Material ......................... 5C-*
Special Tool ........................................................ 5C-*

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GRAND VITARA JB416

Qube AP1 Supplemental Instructions preview
AP1
Brand: Qube Pages: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Brand: Cadillac Pages: 32
CAMPARK R10 Manual preview
R10
Brand: CAMPARK Pages: 20
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Brand: B-Speech Pages: 24
Globalsat MR-350P Installation Manual preview
MR-350P
Brand: Globalsat Pages: 2
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Brand: ULTIMATE SPEED Pages: 6
Meta System 900000358 Installation Technical Sheet preview
900000358
Brand: Meta System Pages: 22
Sanitas SMG 245 Instructions For Use Manual preview
SMG 245
Brand: Sanitas Pages: 36
Z Flash OBD-II STALK User Manual preview
OBD-II STALK
Brand: Z Flash Pages: 4
RAM RAM C 2013 Specification preview
RAM C 2013
Brand: RAM Pages: 5
Xforce PR-104 User Manual preview
PR-104
Brand: Xforce Pages: 11
Setma E12PE27000 Instruction Manual preview
E12PE27000
Brand: Setma Pages: 13
Rosco STSK4730 Installation & User Manual preview
STSK4730
Brand: Rosco Pages: 12
AA Products APX2501 BLK Instruction Manual preview
APX2501 BLK
Brand: AA Products Pages: 8
Vauxhall Antara 2014 Owner'S Manual preview
Antara 2014
Brand: Vauxhall Pages: 215
Metra Electronics 99-7400 Installation Instructions Manual preview
99-7400
Brand: Metra Electronics Pages: 8
P-Charge STAND-ALONE Operating Instructions Manual preview
STAND-ALONE
Brand: P-Charge Pages: 16
XPENG P7 2023 User Manual preview
P7 2023
Brand: XPENG Pages: 316

Brands by name

Popular brands

Load more brands