Suzuki GRAND VITARA JB416 Service Manual Download Page 177

Page: 177 / 474

Transfer: Motor-Shift Type (Transfer with Shift Actuator) 3C-60

Transfer Assembly Disassembly and
Reassembly

S5JB0E3316009

Disassembly

1) Remove harness bracket (1).

2) Remove center differential lock switch (1) and 4L/N

switch (2).

3) Remove transfer actuator assembly (3) and breather

pipe (4).

4) Remove oil pump cover (1).

5) Remove oil pump inner rotor (1), outer rotor (2), oil

strainer (4) and drive pin (3).

1. Front oil seal No.1

: Apply grease 99000-25010 to oil seal lip.

20. Washer

39. Oil strainer bolt

2. Front case bolt

21. Shim

40. Oil pump outer rotor

3. Front case

22. Reduction shift sleeve

41. Oil pump inner rotor

4. Knock pin

23. Center differential assembly

42. Oil pump drive pin

5. Oil pipe

24. Low gear

43. Oil strainer bolt

6. Input gear assembly

25. Front drive shaft

44. Oil pump cover bolt

7. Input gear plate bolt

26. Thrust needle bearing

45. Oil drain plug

: Apply sealant 99000-31260 to
plug thread.

8. Counter gear assembly

27. Differential lock clutch sleeve

46. Transfer to transmission bolt

9. Needle bearing

28. Front drive sprocket bush

47. Front oil seal No.2

: Apply grease 99000-25010 to oil
seal lip.

10. Center case

: Apply sealant 99000-31260 to mating
surface of front case, transfer control
cover and center case.

29. Front drive sprocket

48. Rear oil seal

: Apply grease 99000-25010 to oil
seal lip.

11. Damper

30. Rear output shaft assembly

49. Transfer actuator bolt

12. 4L/N switch

31. Front output shaft assembly

50. Control cover

13. Center differential lock switch

32. Drive chain

: 23 N

⋅

m (2.3 kgf-m, 17.0 lb-ft)

14. Transfer actuator assembly

33. Rear case

: Apply sealant 99000-31260 to mating
surface of rear case, oil pump cover and
center case.

: 10 N

⋅

m (1.0 kgf-m, 7.5 lb-ft)

15. Control cover bolt

: Apply thread lock 99000-32110 to bolt
thread.

34. Oil level / filler plug

: Apply sealant 99000-31260 to plug
thread.

: 50 N

⋅

m (5.0 kgf-m, 36.5 lb-ft)

16. Damper bolt

35. Harness bracket

: 20 N

⋅

m (2.0 kgf-m, 14.5 lb-ft)

17. Breather pipe

36. Harness bracket bolt

: Do not reuse.

18. O-ring

37. Rear case bolt

: Apply transfer oil.

19. Snap ring

38. Oil strainer

I5JB0A331010-01

I5JB0A331011-01

I5JB0A331012-01

I5JB0A331013-01

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Search results

Summary of Contents for GRAND VITARA JB416

Reviews:

Related manuals for GRAND VITARA JB416

Brands by name

Popular brands

Suzuki GRAND VITARA JB416, Service Manual

Search results

Summary of Contents for GRAND VITARA JB416

Reviews:

Related manuals for GRAND VITARA JB416

Brands by name

Popular brands