Suzuki GRAND VITARA JB416 Service Manual Download Page 173

Page: 173 / 474

Transfer: Motor-Shift Type (Transfer with Shift Actuator) 3C-56

7) Apply sealant to thread of level / filler plug, and then

tighten it to specified torque.

“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)

Tightening torque
Transfer oil level / filler plug (b): 23 N·m (2.3 kgf-
m, 17.0 lb-ft)

Transfer Oil Seal Removal and Installation

S5JB0E3316003

Removal

1) Lift up vehicle and drain transfer oil.

2) Remove front propeller shaft and/or rear propeller

shaft referring to “Propeller Shaft Removal and
Installation: in Section 3D in related manual”.

3) Remove front oil seal No.1 (1) and/or rear oil seal (2)

using flat end rod or the like.

“a”. 0 – 10 mm (0 – 0.394 in.)

I5JB0A331002-03

I5JB0A331031-01

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Search results

Summary of Contents for GRAND VITARA JB416

Reviews:

Related manuals for GRAND VITARA JB416

Brands by name

Popular brands

Suzuki GRAND VITARA JB416, Service Manual

Search results

Summary of Contents for GRAND VITARA JB416

Reviews:

Related manuals for GRAND VITARA JB416

Brands by name

Popular brands