manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Service Manual

The Suzuki Grand Vitara JB416 is a versatile SUV known for its reliable performance and rugged design. Whether you need routine maintenance or more extensive repairs, our Service Manual is available for free download at manualshive.com. Keep your vehicle in top condition with our comprehensive manual.

Share
Download
background image

10C-14 Immobilizer Control System: 

DTC P1622: EEPROM Error

S5JB0EA304013

Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: ”

Detecting Condition and Trouble Area

Troubleshooting

1) Clear DTC(s) referring to “Diagnostic Trouble Code (DTC) Clearance:  in related manual”.

2) Turn the ignition switch to OFF position.

3) Check if DTC P1622 is still detected referring to “Diagnostic Trouble Code (DTC) Check:  in related manual”. If still 

detected, go to the next step. If not, the troubleshooting is completed.

4) Replace ECM with new one referring to “Engine Control Module (ECM) Removal and Installation:  in Section 1C in 

related manual”.

5) Perform “Procedure after ECM Replacement:  in related manual”.

DTC P1623: Unregistered Transponder

S5JB0EA304014

Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: ”

Detecting Condition and Trouble Area

Troubleshooting

14

Immobilizer control module (ICM) check

1) Check immobilizer control module (ICM) referring to 

“Inspection of Immobilizer Control Module (ICM) and Its 
Circuit:  in related manual”.

Is immobilizer control module (ICM) normal?

Replace ECM with new 
one referring to “Engine 
Control Module (ECM) 
Removal and 
Installation:  in Section 
1C in related manual”, 
and then perform 
“Procedure after ECM 
Replacement:  in related 
manual”.

Replace immobilizer 
control module (ICM) 
with new one referring 
to “Immobilizer Control 
Module (ICM) Removal 
and Installation:  in 
related manual”.

Step

Action

Yes

No

Detecting Condition

Trouble Area

EEPROM in ECM is corrupted.

Internal failure (EEPROM corruption) of ECM

Detecting Condition

Trouble Area

Transponder code in the transponder built in the ignition 
key is invalid.

• Use of the unregistered ignition key

• Immobilizer control module (ICM) faulty

• ECM faulty

Step

Action

Yes

No

1

Diagnostic Trouble Code (DTC) confirmation

1) Clear DTC(s) referring to “Diagnostic Trouble Code 

(DTC) Clearance:  in related manual”.

2) Turn the ignition switch to OFF position.

3) Check if any DTC is detected referring to “Diagnostic 

Trouble Code (DTC) Check:  in related manual”.

Is DTC P1623 still detected?

Go to Step 2.

The troubleshooting is 
completed.

2

Diagnostic Trouble Code (DTC) check

Is any DTC other than P1623 is detected in Step 1?

Perform the 
troubleshooting 
referring to the 
corresponding 
flowchart, and then go 
to Step 3.

Go to Step 3.

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GRAND VITARA JB416

Daihatsu F300 Service Manual preview
F300
Brand: Daihatsu Pages: 1718
Camoplast T4S User Manual preview
T4S
Brand: Camoplast Pages: 60
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Brand: Jeep Pages: 108
TATA Motors nano genX Owner'S Manual preview
nano genX
Brand: TATA Motors Pages: 156
Yakima Whispbar K887W Fitting Instructions Manual preview
Whispbar K887W
Brand: Yakima Pages: 19
Nav TV UCI-11C NTV-KIT331 User Manual preview
UCI-11C NTV-KIT331
Brand: Nav TV Pages: 4
U.S. General 95904 Operating Instructions preview
95904
Brand: U.S. General Pages: 4
Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Brand: Pontiac Pages: 44
AA Products SR-A260 Instruction Manual preview
SR-A260
Brand: AA Products Pages: 4
Condor T-RAMP Quick Start Manual preview
T-RAMP
Brand: Condor Pages: 2
HAUL MASTER 41782 Assembly And Operating Instructions Manual preview
41782
Brand: HAUL MASTER Pages: 8
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Brand: Chevrolet Pages: 412
Mercedes-Benz E55AMG Service Manual preview
E55AMG
Brand: Mercedes-Benz Pages: 39
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12
Reese Explore 63153 Instruction Manual preview
63153
Brand: Reese Explore Pages: 9
THIEYE CarView 2 User Manual preview
CarView 2
Brand: THIEYE Pages: 88
Buick 1988 Riviera Owner'S Manual preview
1988 Riviera
Brand: Buick Pages: 161

Brands by name

Popular brands

Load more brands