Suzuki GRAND VITARA JB416 Service Manual Download Page 455

Page: 455 / 474

Immobilizer Control System: 10C-17

DTC P1638: Immobilizer Information Mismatched

S5JB0EA304017

Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: ”

DTC Detecting Condition and Trouble Area

Troubleshooting

Detecting Condition

Trouble Area

• The immobilizer control system information in ECM and

the one in BCM does not match.

• The registration of the immobilizer control system

information in ECM is failed.

• Use of the wrong ECM

• Steering angle sensor (if equipped) faulty

• Keyless start control module (if equipped) faulty

• 4WD control module (if equipped)

• TCM (if equipped) faulty

• CAN communication wire circuits faulty

• BCM faulty

• Combination meter faulty

• ABS/ESP

control module faulty

• ECM faulty

Step

Action

Yes

Diagnostic Trouble Code (DTC) confirmation

1) Clear DTC(s) referring to “Diagnostic Trouble Code

(DTC) Clearance: in related manual”.

2) Turn the ignition switch to OFF position.

3) Check if any DTC is detected referring to “Diagnostic

Trouble Code (DTC) Check: in related manual”.

Is DTC P1638 still detected?

Go to Step 2.

The troubleshooting is
completed.

Diagnostic Trouble Code (DTC) confirmation

1) Disconnect negative (–) cable from battery for more than

5 seconds.

2) Connect negative (–) cable to battery.

3) Check if any DTC is detected referring to “Diagnostic

Trouble Code (DTC) Check: in related manual”.

Is DTC P1638 still detected?

Go to Step 3.

The troubleshooting is
completed.

Check ECM specification

1) Check ECM part number to see if ECM is applicable to

the vehicle in service.

Is a correct ECM used for the vehicle in service?

Go to Step 2.

Replace ECM with the
correct one and recheck
if DTC P1638 is still
detected by ECM.

Diagnostic Trouble Code (DTC) check in ECM

Is any DTC other than P1638 detected in Step 1?

Perform the
troubleshooting
referring to the
corresponding
flowchart.

Go to Step 3.

Diagnostic Trouble Code (DTC) check in BCM

1) Check BCM for DTC referring to “DTC Check: in

Section 10B in related manual”.

Is any DTC detected?

Perform the
troubleshooting
referring to the
corresponding flowchart
in Section 10B.

Go to Step 5.

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Search results

Summary of Contents for GRAND VITARA JB416

Reviews:

Related manuals for GRAND VITARA JB416

Brands by name

Popular brands

Suzuki GRAND VITARA JB416, Service Manual

Search results

Summary of Contents for GRAND VITARA JB416

Reviews:

Related manuals for GRAND VITARA JB416

Brands by name

Popular brands