manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Service Manual

The Suzuki Grand Vitara JB416 is a versatile SUV known for its reliable performance and rugged design. Whether you need routine maintenance or more extensive repairs, our Service Manual is available for free download at manualshive.com. Keep your vehicle in top condition with our comprehensive manual.

Share
Download
background image

Immobilizer Control System:  10C-15

DTC P1625: Immobilizer Antenna Error

S5JB0EA304015

Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: ”

Detecting Condition and Trouble Area

Troubleshooting

3

Registration of the unregistered ignition key with ECM 
and Diagnostic Trouble Code (DTC) check

1) Register the transponder code in the transponder in the 

unregistered ignition key with ECM referring to 
“Registration of the Ignition Key:  in related manual”.

2) Check if that DTC P1623 is detected referring to 

“Diagnostic Trouble Code (DTC) Check:  in related 
manual”.

Is DTC P1623 detected?

Go to Step 4.

The troubleshooting is 
completed.

4

Immobilizer control module (ICM) check

1) Check immobilizer control module (ICM) referring to 

“Inspection of Immobilizer Control Module (ICM) and Its 
Circuit:  in related manual”.

Is immobilizer controller assembly normal?

Replace ECM with new 
one referring to “Engine 
Control Module (ECM) 
Removal and 
Installation:  in Section 
1C in related manual”, 
and then perform 
“Procedure after ECM 
Replacement:  in related 
manual”.

Replace immobilizer 
control module (ICM) 
with new one referring 
to “Immobilizer Control 
Module (ICM) Removal 
and Installation:  in 
related manual”.

Step

Action

Yes

No

Detecting Condition

Trouble Area

Immobilizer control module (ICM) is faulty.

• Immobilizer control module faulty

• ECM faulty

Step

Action

Yes

No

1

Diagnostic Trouble Code (DTC) confirmation

1) Clear DTC(s) referring to “Diagnostic Trouble Code 

(DTC) Clearance:  in related manual”.

2) Turn the ignition switch to OFF position.

3) Check if any DTC is detected referring to “Diagnostic 

Trouble Code (DTC) Check:  in related manual”.

Is DTC P1625 still detected?

Go to Step 2.

The troubleshooting is 
completed.

2

Immobilizer control module (ICM) replacement and 
Diagnostic Trouble Code (DTC) check

1) Replace immobilizer control module (ICM) referring to 

“Immobilizer Control Module (ICM) Removal and 
Installation:  in related manual”.

2) Check if DTC P1625 is still detected referring to 

“Diagnostic Trouble Code (DTC) Check:  in related 
manual”.

Is DTC P1625 still detected?

Replace ECM with new 
one referring to “Engine 
Control Module (ECM) 
Removal and 
Installation:  in Section 
1C in related manual”, 
and then perform 
“Procedure after ECM 
Replacement:  in related 
manual”.

The troubleshooting is 
completed.

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GRAND VITARA JB416

Subaru SPLASH GUARD Installation Manual preview
SPLASH GUARD
Brand: Subaru Pages: 3
Porsche 911 GT3 - Brochure preview
911 GT3 -
Brand: Porsche Pages: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Brand: Whispbar Pages: 14
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Brand: Atwood Pages: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Brand: BMW Pages: 21
Yakima K674 Instructions Manual preview
K674
Brand: Yakima Pages: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Brand: Menabo Pages: 11
Gator HUDGPS1 Quick Start Manual preview
HUDGPS1
Brand: Gator Pages: 2
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Brand: VER-MAC Pages: 64
GMC TopKick 2007 Owner'S Manual preview
TopKick 2007
Brand: GMC Pages: 430
Reliant ROBIN 850 Workshop Manual preview
ROBIN 850
Brand: Reliant Pages: 206
MMD 41240 Quick Manual preview
41240
Brand: MMD Pages: 3
Ford TRANSIT 2015 Quick Reference Manual preview
TRANSIT 2015
Brand: Ford Pages: 8
Nos 05183NOS Owner'S Manual preview
05183NOS
Brand: Nos Pages: 22
Nav TV MOST-HUR31 Manual preview
MOST-HUR31
Brand: Nav TV Pages: 8
Haltech NEXUS R3 Quick Start Manual preview
NEXUS R3
Brand: Haltech Pages: 13
Kleinn Air Horns RNGR-102-1/220 Installation Manual preview
RNGR-102-1/220
Brand: Kleinn Air Horns Pages: 33
Ford 2003 Ranger Quick Reference Manual preview
2003 Ranger
Brand: Ford Pages: 2

Brands by name

Popular brands

Load more brands