manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Service Manual

The Suzuki Grand Vitara JB416 is a versatile SUV known for its reliable performance and rugged design. Whether you need routine maintenance or more extensive repairs, our Service Manual is available for free download at manualshive.com. Keep your vehicle in top condition with our comprehensive manual.

Share
Download
background image

Table of Contents 1-iii

Aux. Emission Control Devices ..............1B-*

Diagnostic Information and Procedures............ 1B-*

EGR System Inspection .......................................1B-*

Repair Instructions .............................................. 1B-*

EVAP Canister Purge Inspection .........................1B-*
EVAP Canister Purge Valve and Its Circuit 

Inspection...........................................................1B-*

Vacuum Passage Inspection ...............................1B-*
Vacuum Hose and Purge Valve Chamber 

Inspection...........................................................1B-*

EVAP Canister Purge Valve Inspection ...............1B-*
EVAP Canister Inspection....................................1B-*
EGR Valve Removal and Installation ...................1B-*
EGR Valve Inspection ..........................................1B-*
PCV Hose Inspection ...........................................1B-*
PCV Valve Removal and Installation ...................1B-*
PCV Valve Inspection ..........................................1B-*

Specifications....................................................... 1B-*

Tightening Torque Specifications.........................1B-*

Special Tools and Equipment ............................. 1B-*

Recommended Service Material ..........................1B-*
Special Tool .........................................................1B-*

Engine Electrical Devices ........................1C-*

Repair Instructions .............................................. 1C-*

Engine Control Module (ECM) Removal 

and Installation .................................................. 1C-*

Manifold Absolute Pressure (MAP) Sensor 

Inspection.......................................................... 1C-*

Electric Throttle Body Assembly 

On-Vehicle Inspection ....................................... 1C-*

Electric Throttle Body System Calibration........... 1C-*
Accelerator Pedal Position (APP) Sensor 

Assembly On-Vehicle Inspection ...................... 1C-*

Accelerator Pedal Position (APP) Sensor 

Assembly Removal and Installation .................. 1C-*

Accelerator Pedal Position (APP) Sensor 

Assembly Inspection ......................................... 1C-*

Engine Coolant Temperature (ECT) Sensor 

Removal and Installation................................... 1C-*

Engine Coolant Temperature (ECT) 

Sensor Inspection ............................................. 1C-*

Air Fuel Ratio (A/F) Sensor On-Vehicle 

Inspection.......................................................... 1C-*

Heated Oxygen Sensor (HO2S-2) Heater 

On-Vehicle Inspection ....................................... 1C-*

Air Fuel Ratio (A/F) Sensor, Heated Oxygen 

Sensor (HO2S-2) Removal and Installation ...... 1C-*

Camshaft Position (CMP) Sensor Removal 

and Installation .................................................. 1C-*

Camshaft Position (CMP) Sensor 

Inspection.......................................................... 1C-*

Crankshaft Position (CKP) Sensor 

Removal and Installation................................... 1C-*

Crankshaft Position (CKP) Sensor 

Inspection.......................................................... 1C-*

Knock Sensor Removal and Installation ............. 1C-*
Control Relay Inspection ..................................... 1C-*

Mass Air Flow (MAF) and Intake Air 

Temperature (IAT) Sensor On-Vehicle 
Inspection.......................................................... 1C-*

Mass Air Flow (MAF) and Intake Air 

Temperature (IAT) Sensor Removal and 
Installation ......................................................... 1C-*

Mass Air Flow (MAF) and Intake Air 

Temperature (IAT) Sensor Inspection............... 1C-*

Vacuum Tank Assembly Inspection (For 

J20 Engine) ....................................................... 1C-*

Electric Load Current Sensor On-Vehicle 

Inspection (For J20 Engine) .............................. 1C-*

Electric Load Current Sensor Removal 

and Installation (For J20 Engine) ...................... 1C-*

Specifications ....................................................... 1C-*

Tightening Torque Specifications........................ 1C-*

Engine Mechanical ...................................1D-*

For M16A Engine with VVT..................................... 1D-*

General Description ............................................. 1D-*

Engine Construction Description......................... 1D-*
Camshaft Position Control (VVT Variable 

Valve Timing) System Description .................... 1D-*

Diagnostic Information and Procedures ............ 1D-*

Compression Check............................................ 1D-*
Engine Vacuum Check........................................ 1D-*
Valve Lash (Clearance) Inspection ..................... 1D-*

Repair Instructions .............................................. 1D-*

Air Cleaner Filter Removal and Installation......... 1D-*
Air Cleaner Filter Inspection and Cleaning.......... 1D-*
Cylinder Head Cover Removal and 

Installation ......................................................... 1D-*

Throttle Body and Intake Manifold 

Components...................................................... 1D-*

Throttle Body On-Vehicle Inspection................... 1D-*
Electric Throttle Body Assembly Removal 

and Installation .................................................. 1D-*

Throttle Body Cleaning........................................ 1D-*
Intake Manifold Removal and Installation ........... 1D-*
Engine Mountings Components .......................... 1D-*
Engine Assembly Removal and Installation ........ 1D-*
Timing Chain Cover Components ....................... 1D-*
Timing Chain Cover Removal and 

Installation ......................................................... 1D-*

Timing Chain Cover Inspection ........................... 1D-*
Oil Control Valve Removal and Installation......... 1D-*
Oil Control Valve Inspection................................ 1D-*
Timing Chain and Chain Tensioner 

Components...................................................... 1D-*

Timing Chain and Chain Tensioner 

Removal and Installation................................... 1D-*

Timing Chain and Chain Tensioner 

Inspection.......................................................... 1D-*

Camshaft, Tappet and Shim Components .......... 1D-*
Camshaft, Tappet and Shim Removal and 

Installation ......................................................... 1D-*

Camshaft, Tappet and Shim Inspection .............. 1D-*
Valves and Cylinder Head Components ............. 1D-*

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GRAND VITARA JB416

Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Brand: Kolpin Pages: 25
FormFit HD 10L07 Installation Instructions preview
HD 10L07
Brand: FormFit Pages: 2
Yakima RoadShower 10G Quick Start Manual preview
RoadShower 10G
Brand: Yakima Pages: 12
Rightline Gear Car Top Duffle Bag Setup Manual preview
Car Top Duffle Bag
Brand: Rightline Gear Pages: 2
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Brand: Pyle Pages: 4
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Brand: hc-cargo Pages: 60
PAC GM1A-R Quick Start Manual preview
GM1A-R
Brand: PAC Pages: 4
Bestop 614.04 Installation Manual preview
614.04
Brand: Bestop Pages: 31
Westin 31-0190 Installation Instructions preview
31-0190
Brand: Westin Pages: 2
Demco TP20047 Assembly Operation Replacement Parts preview
TP20047
Brand: Demco Pages: 4
ConWys AG 21500598C VW Fitting Instructions Manual preview
21500598C VW
Brand: ConWys AG Pages: 16
Honda 2009 S2000 Owner'S Manual preview
2009 S2000
Brand: Honda Pages: 268
Mobridge DA-G2 MOST150 Manual preview
DA-G2 MOST150
Brand: Mobridge Pages: 20
Kleinn RS-GM6 Installation Manual preview
RS-GM6
Brand: Kleinn Pages: 8
Menabo YELO 4 NS Fitting Instructions Manual preview
YELO 4 NS
Brand: Menabo Pages: 8
TOP VEHICLE TECH GR3FORD5 Installation Manual preview
GR3FORD5
Brand: TOP VEHICLE TECH Pages: 8
Brodit Getac T800 Quick Start Manual preview
Getac T800
Brand: Brodit Pages: 2
Saturn 2009 OUTLOOK Owner'S Manual preview
2009 OUTLOOK
Brand: Saturn Pages: 432

Brands by name

Popular brands

Load more brands