manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Service Manual

The Suzuki Grand Vitara JB416 is a versatile SUV known for its reliable performance and rugged design. Whether you need routine maintenance or more extensive repairs, our Service Manual is available for free download at manualshive.com. Keep your vehicle in top condition with our comprehensive manual.

Share
Download
background image

9-iv Table of Contents

Front Speaker Removal and Installation ............. 9C-*
Rear Speaker Removal and Installation (5 

Door Model) ...................................................... 9C-*

Rear Speaker Removal and Installation (3 

Door Model) ...................................................... 9C-*

GPS Antenna Removal and Installation (If 

Equipped).......................................................... 9C-*

Horn Removal and Installation ............................ 9C-*
Horn Inspection ................................................... 9C-*
Horn Relay Inspection......................................... 9C-*
Antenna Base Removal and Installation ............. 9C-*
Remote Audio Control Switch Removal 

and Installation .................................................. 9C-*

Remote Audio Control Switch Inspection............9C-9

Wipers / Washers .................................... 9D-1

Diagnostic Information and Procedures ............ 9D-*

Front Wiper and Washer Symptom 

Diagnosis .......................................................... 9D-*

Rear Wiper and Washer Symptom 

Diagnosis (If Equipped)..................................... 9D-*

Headlight Washer Symptom Diagnosis (If 

Equipped).......................................................... 9D-*

Headlight Washer Operation Inspection ............. 9D-*
Inspection of Headlight Washer Control 

Module and Its Circuit ....................................... 9D-*

Repair Instructions ..............................................9D-1

Wipers and Washers Components ..................... 9D-*
Washer Tank and Washer Pump Removal 

and Installation .................................................. 9D-*

Washer Pump Inspection .................................... 9D-*
Windshield Wiper Removal and Installation........ 9D-*
Windshield Wiper Motor Inspection..................... 9D-*
Rear Wiper Removal and Installation (If 

Equipped).......................................................... 9D-*

Rear Wiper Motor Inspection (If Equipped)......... 9D-*
Windshield Wiper and Washer Switch 

Removal and Installation................................... 9D-*

Windshield Wiper and Washer Switch 

Inspection..........................................................9D-1

Rear Wiper and Washer Switch Removal 

and Installation .................................................. 9D-*

Rear Wiper and Washer Switch Inspection.........9D-3

Rear Wiper Relay Removal and Installation ....... 9D-*
Rear Wiper Relay Inspection .............................. 9D-*
Headlight Washer Switch Inspection (If 

Equipped).......................................................... 9D-*

Headlight Washer Pump Removal and 

Installation (If Equipped) ................................... 9D-*

Headlight Washer Nozzle Removal and 

Installation (If Equipped) ................................... 9D-*

Specifications....................................................... 9D-*

Tightening Torque Specifications........................ 9D-*

Glass / Windows / Mirrors ....................... 9E-*

General Description ............................................. 9E-*

Rear End Door Window Defogger System 

Description ........................................................ 9E-*

Windshield Construction ..................................... 9E-*
Rear Quarter Window Construction .................... 9E-*

Diagnostic Information and Procedures ............ 9E-*

Rear End door Window Defogger Symptom 

Diagnosis .......................................................... 9E-*

Power Window Control System Symptom 

Diagnosis .......................................................... 9E-*

Power Door Mirror Control System 

Symptom Diagnosis (If Equipped)..................... 9E-*

Door Mirror Heater Symptom Diagnosis (If 

Equipped).......................................................... 9E-*

Repair Instructions .............................................. 9E-*

Windshield Removal and Installation .................. 9E-*
Rear Quarter Window Removal and 

Installation ......................................................... 9E-*

Front Door Window Components ........................ 9E-*
Front Door Glass Removal and Installation ........ 9E-*
Front Door Window Regulator Removal 

and Installation .................................................. 9E-*

Front Door Window Regulator Inspection ........... 9E-*
Rear Door Window Components ........................ 9E-*
Rear Door Glass Removal and Installation ......... 9E-*
Rear Door Window Regulator Removal 

and Installation .................................................. 9E-*

Rear Door Window Regulator Inspection ............ 9E-*
Rear End Door Window Components ................. 9E-*
Rear End Door Glass Removal and 

Installation ......................................................... 9E-*

Rear End Door Window Defogger Relay 

Inspection.......................................................... 9E-*

Rear End Door Window Defogger Wire 

Inspection.......................................................... 9E-*

Rear End Door Window Defogger Wire 

Repair................................................................ 9E-*

Power Window Main Switch Inspection .............. 9E-*
Power Window Sub Switch Inspection ................ 9E-*
Door Mirror Components..................................... 9E-*
Door Mirror Removal and Installation.................. 9E-*
Power Door Mirror Switch Inspection (If 

Equipped).......................................................... 9E-*

Power Door Mirror Actuator Inspection (If 

Equipped).......................................................... 9E-*

Door Mirror Heater Inspection (If Equipped) ....... 9E-*
Door Mirror Heater Relay Inspection (If 

Equipped).......................................................... 9E-*

Special Tools and Equipment ............................. 9E-*

Recommended Service Material ......................... 9E-*

Security and Locks................................... 9F-*

General Description ..............................................9F-*

Key Coding Construction .....................................9F-*

Component Location ............................................9F-*

Power Door Lock and Keyless Entry 

System Component Location .............................9F-*

Diagnostic Information and Procedures .............9F-*

Power Door Lock System Symptom 

Diagnosis ...........................................................9F-*

Power Door Lock System Operation 

Inspection...........................................................9F-*

Keyless Entry System Symptom Diagnosis 

(If Equipped).......................................................9F-*

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GRAND VITARA JB416

Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Brand: hager Pages: 9
Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Brand: Jeep Pages: 608
PAC SWI-RC Installation Instructions preview
SWI-RC
Brand: PAC Pages: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Brand: PAC Pages: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Brand: PAC Pages: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Brand: PAC Pages: 5
Vauxhall INSIGNIA 2017 Owner'S Manual preview
INSIGNIA 2017
Brand: Vauxhall Pages: 323
TrailFX A4012S Installation Instructions Manual preview
A4012S
Brand: TrailFX Pages: 6
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Brand: minnid Pages: 44
Jaeger J05252127 Fitting Instructions Manual preview
J05252127
Brand: Jaeger Pages: 17
Fab Fours VI-COWL Installation Instructions Manual preview
VI-COWL
Brand: Fab Fours Pages: 19
Kia 2014 rondo Features preview
2014 rondo
Brand: Kia Pages: 11
Saab 2008 9-7x Owner'S Manual preview
2008 9-7x
Brand: Saab Pages: 426
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Brand: Mynew Pages: 5
Cadillac XLR-V Specifications preview
XLR-V
Brand: Cadillac Pages: 2
Buick Cascada 2016 Getting To Know Manual preview
Cascada 2016
Brand: Buick Pages: 20

Brands by name

Popular brands

Load more brands