manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Service Manual

The Suzuki Grand Vitara JB416 is a versatile SUV known for its reliable performance and rugged design. Whether you need routine maintenance or more extensive repairs, our Service Manual is available for free download at manualshive.com. Keep your vehicle in top condition with our comprehensive manual.

Share
Download
background image

10-ii Table of Contents

Immobilizer Control System Introduction .......... 10C-*
Immobilizer Control System Components 

Location .......................................................... 10C-*

On-Board Diagnostic System Description 

(Self-diagnosis Function) ................................ 10C-*

Schematic and Routing Diagram ......................10C-2

Immobilizer Control System Wiring Circuit 

Diagram ..........................................................10C-2

Diagnostic Information and Procedures ..........10C-3

Immobilizer Control System Check ................... 10C-*
Diagnostic Trouble Code (DTC) Check............. 10C-*
Diagnostic Trouble Code (DTC) Clearance ...... 10C-*

Diagnostic Trouble Code (DTC) Table..............10C-3

Scan Tool Data ................................................. 10C-*
Immobilizer Indicator Lamp Does Not Come 

ON with Ignition Switch ON and Engine 
Stop................................................................. 10C-*

Immobilizer Indicator Lamp Remains ON 

after Engine Start ............................................ 10C-*

DTC P1614: Transponder Response Error.......10C-4
DTC P1615: Steering Lock Unit 

Communication Error (for Vehicle with 
Keyless Start System).....................................10C-5

DTC P1616: Unregistered Keyless Start 

Control Module (for Vehicle with Keyless 
Start System) ..................................................10C-8

DTC P1618: Keyless Start Control Module 

CAN Communication Error (for Vehicle with 
Keyless Start System).....................................10C-9

DTC P1621: Immobilizer Communication 

Line Error ......................................................10C-11

DTC P1622: EEPROM Error...........................10C-14
DTC P1623: Unregistered Transponder .........10C-14
DTC P1625: Immobilizer Antenna Error..........10C-15
DTC P1636: Immobilizer Information 

Registration Failure .......................................10C-16

DTC P1638: Immobilizer Information 

Mismatched...................................................10C-17

Inspection of Immobilizer Control Module 

(ICM) and Its Circuit ........................................ 10C-*

Repair Instructions ............................................ 10C-*

Immobilizer Control Module (ICM) Removal 

and Installation ................................................ 10C-*

Registration of the Ignition Key ......................... 10C-*
Procedure after ECM Replacement .................. 10C-*

Special Tools and Equipment ........................... 10C-*

Special Tool ...................................................... 10C-*

Keyless Start System .............................10E-1

General Description ........................................... 10E-1

Keyless Start System Description ..................... 10E-*
Parts and Functions .......................................... 10E-*
Keyless Engine Start Function .......................... 10E-*
Door Lock Function of Keyless Start System.... 10E-*

Operation Area of Remote Controller................ 10E-1

Alarm Function .................................................. 10E-*

CAN Communication System Description......... 10E-2

Schematic and Routing Diagram ......................10E-3

Keyless Start System Electric Wiring 

Circuit Diagram ...............................................10E-3

Diagnostic Information and Procedures ..........10E-4

Precautions in Diagnosing Troubles .................10E-4

Self-Diagnosis Function .................................... 10E-*
Keyless Start System Diagnosis 

Introduction ..................................................... 10E-*

Keyless Start System Check ............................. 10E-*
Customer Questionnaire (Example) .................. 10E-*
Key Indicator Lamp Check ................................ 10E-*

DTC Check........................................................10E-4

DTC Table ......................................................... 10E-*
DTC Clearance ................................................. 10E-*
Keyless Start System Symptom Diagnosis ....... 10E-*
Keyless Start System Operation Inspection ...... 10E-*
Door Lock Operation (Keyless Start 

System) ........................................................... 10E-*

Inspection of Keyless Start Control Module 

and Its Circuits ................................................10E-6

No DTC Detection After Performing DTC 

Check .............................................................. 10E-*

Key Indicator Lamp Circuit Check (Key 

Indicator Lamp Doesn’t Light when Ignition 
Knob Switch is Pushed.) ................................. 10E-*

Keyless Start Control Module Power and 

Ground Circuit Check...................................... 10E-*

DTC No. 11: Communication Error with 

Steering Lock Unit........................................... 10E-*

DTC No. 13 / No. 14: Release Signal Error 

from Steering Lock Unit / Steering Lock 
Unit Malfunction .............................................. 10E-*

DTC No. 21 / No. 22: Internal Error of 

Keyless Start Control Module (EEPROM 
Reading Error) / (EEPROM Writing Error) ...... 10E-*

DTC No. 31: Lost Communication with BCM ..10E-12
DTC No. 33: Control Module Communication 

Bus Off ..........................................................10E-15

DTC No. 51 / No. 52 / No. 53: Driver Side / 

Passenger Side / Rear End Door Request 
Switch Failure.................................................. 10E-*

Repair Instructions ............................................ 10E-*

Antennas and Request Switches Removal 

and Installation ................................................ 10E-*

Front Door (Driver and Passenger Side), 

Rear End Door Request Switch Inspection..... 10E-*

Steering Lock Unit Removal and Installation .... 10E-*
Steering Lock Unit Inspection ........................... 10E-*
Front Door Lock Switch Inspection ................... 10E-*
Keyless Start Control Module Removal 

and Installation ................................................ 10E-*

Remote Controller Inspection............................ 10E-*
Replacement of Remote Controller Battery ...... 10E-*
Registration Procedure for Remote 

Controller ID Code .......................................... 10E-*

Summary of Contents for GRAND VITARA JB416



























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GRAND VITARA JB416

Vauxhall Meriva Quick Reference Manual preview
Meriva
Brand: Vauxhall Pages: 2
Vauxhall Ampera Quick Reference Manual preview
Ampera
Brand: Vauxhall Pages: 2
Vauxhall 2012 Agila Quick Reference Manual preview
2012 Agila
Brand: Vauxhall Pages: 2
Vauxhall 2013 Mokka Owner'S Manual preview
2013 Mokka
Brand: Vauxhall Pages: 209
VBC Racing WildFire Instruction Manual preview
WildFire
Brand: VBC Racing Pages: 34
Vauxhall 2013 Corsa Infotainment system Quick Reference Manual preview
2013 Corsa Infotainment system
Brand: Vauxhall Pages: 2
Vauxhall 2010 Astra Quick Reference Manual preview
2010 Astra
Brand: Vauxhall Pages: 2
Vauxhall Antara Owner'S Manual preview
Antara
Brand: Vauxhall Pages: 236
GMC 2005 Sierra Denali Owner'S Manual preview
2005 Sierra Denali
Brand: GMC Pages: 428
Mercedes-Benz GLA 250 2019 Operator'S Manual preview
GLA 250 2019
Brand: Mercedes-Benz Pages: 346
Thule Kit 1514 Instructions preview
Kit 1514
Brand: Thule Pages: 4
Dometic GROUP DRS2 Installation And Operating Manual preview
DRS2
Brand: Dometic GROUP Pages: 20
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Brand: B-Speech Pages: 24
Sirius Satellite Radio Streamer GTR Installation Manual preview
Streamer GTR
Brand: Sirius Satellite Radio Pages: 8
Phonocar 4/084 Mounting Instructions preview
4/084
Brand: Phonocar Pages: 2
Actia SmarTach Manual preview
SmarTach
Brand: Actia Pages: 102
Anker Technology Roav VIVA Owner'S Manual preview
Roav VIVA
Brand: Anker Technology Pages: 8
Kuda 076100 Installation Instruction preview
076100
Brand: Kuda Pages: 3

Brands by name

Popular brands

Load more brands