manualshive.com logo in svg

Siemens sinamics dcp, Manual, Page: 404 / 518

Share
Download
Siemens sinamics dcp Manual Download Page 404

4 Faults and alarms
4.2 List of faults and alarms

SINAMICS DCP

404

 

List Manual (LH21), 05/2016

For fault value = 208:
Check parameter p0430.23 and reset if necessary.

A01304 (F)

Firmware version of DRIVE-CLiQ component is not up-to-date

Drive object:

CU_DCP, TM150, TM15DI_DO, TM31

Cause:

The non-volatile memory has a more recent firmware version than the one in the connected DRIVE-CLiQ 
component.
Alarm value (r2124, interpret decimal):
Component number of the DRIVE-CLiQ component involved.

Remedy:

Update the firmware (p7828, p7829 and commissioning software).

F01305

Topology: Component number missing

Drive object:

CU_DCP, TM150, TM15DI_DO, TM31

Cause:

The component number from the topology was not parameterized (p0121 (for power unit, refer to p0107), p0131 (for 
servo/vector drives, refer to p0107), p0141, p0151, p0161).
Fault value (r0949, interpret decimal):
Data set number.
Note:
The fault also occurs if encoders have been configured (p0187 to p0189) but no component numbers exist for them.
In this case, the fault value includes the drive data set number plus 100 * encoder number (e.g. 3xx, if a component 
number was not entered in p0141 for encoder 3 (p0189)).
See also: p0151 (Terminal Module component number)

Remedy:

- enter missing component number.
- if required, remove the component and restart commissioning.
See also: p0151 (Terminal Module component number)

A01306

Firmware of the DRIVE-CLiQ component being updated

Drive object:

CU_DCP, TM150, TM15DI_DO, TM31

Cause:

Firmware update is active for at least one DRIVE-CLiQ component.
Alarm value (r2124, interpret decimal):
Component number of the DRIVE-CLiQ component.

Remedy:

Not necessary.
This alarm automatically disappears after the firmware has been updated.

A01314

Topology: Component must not be present

Drive object:

TM150, TM15DI_DO, TM31

Cause:

For a component, "de-activate and not present" is set but this component is still in the topology.
Alarm value (r2124, interpret hexadecimal):
ddccbbaa hex:
aa = component number
bb = component class of the component
cc = connection number
Note:
Component class and connection number are described in F01375.

Remedy:

- remove the corresponding component.
- change the setting "de-activate and not present".
Note:
Under "Topology --> Topology view" the commissioning software where relevant offers improved diagnostics 
capability (e.g. setpoint/actual value comparison).
See also: p0105 (Activate/de-activate drive object)

A01315

Drive object not ready for operation

Drive object:

CU_DCP, TM150, TM15DI_DO, TM31

Cause:

For the active drive object involved, at least one activated component is missing.
Note:
All other active and operational drive objects can be in the "RUN" state.

Summary of Contents for sinamics dcp







































































































































































































































































































































































































































































































































Reviews:

No comments