manualshive.com logo in svg

Siemens simovert masterdrives, Compendium, Page: 1196 / 1547

Share
Download
Siemens simovert masterdrives Compendium Download Page 1196

Parameter

Description

Data

Read/write

P204

Pos Reg Kv

204

Function parameter for entering the Kv factor for the 

position controller in [mm/min]/[

μ

m]

index1: 0,100

Min: 0,000

Max: 20,000

Unit: -

Indices: 4 

,FDS

Type: O2

Menus: 

- Parameter menu

  + Control/gating unit

     + Position control

- Upread/free access

Changeable in: 

- Ready to switch on

- Operation enabled

P205*

V rat

205

Rated speed for position control. At this parameter the 

speed resulting at 100 % speed actual-value of the motor 

has to be indicated. The unit is 1000(LE/min), preferably 

(mm/min).

The factory setting value refers to a motor with 3000 (rpm) 

and an actual value weighting factor of 1.0.

In function diagram 340.3

Init: 12288

Min: 1

Max: 

2000000000

Unit: -

Indices: -

Type: O4

Menus: 

- Parameter menu

  + Control/gating unit

     + Position control

- Upread/free access

Changeable in: 

- Ready to switch on

P206*

Pos Reg Time

206

Function parameter for entering the reset time of the 

position controller. 

  0 = Position controller works as a P controller 

>0 = Position controller works as a PI controller

index1: 0

Min: 0

Max: 10000

Unit: ms

Indices: 4 

,FDS

Type: O2

Menus: 

- Parameter menu

  + Control/gating unit

     + Position control

- Upread/free access

Changeable in: 

- Ready to switch on

- Operation enabled

P207*

PosRegLimitFix

207

Function parameter for entering the position controller 

limits. The absolute amount to which the output of the 

position controller is to be limited. The limitation is 

effective both in a positive and a negative direction.

index1: 100,0

Min: 0,0

Max: 199,9

Unit: %

Indices: 4 

,FDS

Type: O2

Menus: 

- Parameter menu

  + Control/gating unit

     + Position control

- Upread/free access

Changeable in: 

- Ready to switch on

- Operation enabled

r208

PosRegGain(act)

208

Actually active KP factor of the position controller with the 

influencing variables Kv factor, Kv adaption, AVWF  and 

rated speed. With this factor the deviation of the position 

control is multiplied. The KP factor additionally includes 

conversion of the normalization to the internal % 

representation.

KP = (AVWF * Kv)/Vrat *4000 0000h (corresponds to 100 

%)

AVWF = Actual value weighting factor (in german: IBF)

Kv = Gain of position control loop

Vrat = rated speed

In function diagram 340.4

Dec.Plc.: 0

Unit: -

Indices: -

Type: I4

Menus: 

- Parameter menu

  + Control/gating unit

     + Position control

- Upread/free access

P209*

S.PRE PosReg

209

Parameter for selecting the connector which supplies the 

speed pre-control value. This usually comes from the 

technology, synchronous operation or positioning.

In Function diagram 340.1

index1: 312

Unit: -

Indices: 2 

,BDS

Type: L2 ,K 

,K

Menus: 

- Parameter menu

  + Control/gating unit

     + Position control

- Upread/free access

Changeable in: 

- Ready to switch on

- Operation enabled

P210*

S.1 Rel PosReg

210

BICO parameter for selecting the binector from which the 

1st command for releasing the position controller is to be 

read in.

index1: 0

Unit: -

Indices: 2 

,BDS

Type: L2 ,B

Menus: 

- Parameter menu

  + Control/gating unit

     + Position control

- Upread/free access

Changeable in: 

- Ready to switch on

- Operation enabled

36

Siemens AG     6SE7087-6QX70 (Edition AL)
SIMOVERT MASTERDRIVES   Compendium Motion Control

Summary of Contents for simovert masterdrives












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments