manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual

The Freescale Semiconductor Symphony DSP56724 is a cutting-edge product that offers high-performance digital signal processing capabilities. Unlock its full potential with the comprehensive Reference Manual, available for free download from our website. Experience enhanced functionality and optimize your user experience with this invaluable manual.

Share
Download
background image

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

19-16

Freescale Semiconductor

 

Asynchronous Sample Rate Converter

19.2.2.6

ASRC Clock Divider Registers (ASRCDR1, ASRCDR2)

The Clock Divider registers (ASRCDR1, ASRCDR2) are two 24-bit read/write registers that control the 
division factors of the ASRC input and output clock sources.

Figure 19-10. Clock Divider Register-1 (ASRCDR1)

7–4

AICSB

Input Clock Source B

0000 ESAI Rx clock
0001 ESAI-1 Rx clock
0010 ESAI-2 Rx clock
0011 ESAI-3 Rx clock
0100 S/PDIF Rx clock
0101 Reserved
0110 Reserved
Any other value—ASRCK1 (In DSP56724/DSP56725, this signal is derived from the PLL, and can be 
controlled by the ASCDR register in the CGM module.)

3–0

AICSA

Input Clock Source A

0000 ESAI Rx clock
0001 ESAI-1 Rx clock
0010 ESAI-2 Rx clock
0011 ESAI-3 Rx clock
0100 S/PDIF Rx clock
0101 Reserved
0110 Reserved
Any other value—ASRCK1 (In DSP56724/DSP56725, this signal is derived from the PLL, and can be 
controlled by the ASCDR register in the CGM module.)

Offset 0x6

Access: User Read/Write

23

22

21

20

19

18

17

16

15

14

13

12

R

AOCDB

AOCPB

AOCDA

AOCPA

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

11

10

9

8

7

6

5

4

3

2

1

0

R

AICDB

AICPB

AICDA

AICPA

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

Table 19-9. Clock Source Register (ASRCSR) (Continued)

Bit

Field

Description

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Symphony DSP56724

NEC NP-PX700W Technical Data Sheet preview
NP-PX700W
Brand: NEC Pages: 2
Speaka Professional SP-9370956 Operating Instructions Manual preview
SP-9370956
Brand: Speaka Professional Pages: 68
Navitar 484MCZ500 Installation Instructions preview
484MCZ500
Brand: Navitar Pages: 1
Avamix REVOLUTION 928BFP34 Quick Start Manual preview
REVOLUTION 928BFP34
Brand: Avamix Pages: 9
DS Produkte KC99 Instructions preview
KC99
Brand: DS Produkte Pages: 4
Anvil BCA7003 Specifications preview
BCA7003
Brand: Anvil Pages: 2
Goldair FFC100 Series Operating Instructions preview
FFC100 Series
Brand: Goldair Pages: 5
DAS DSP-26 User Manual preview
DSP-26
Brand: DAS Pages: 44
SAPIRHOME SP-1111-K Instruction Manual preview
SP-1111-K
Brand: SAPIRHOME Pages: 9
RCA RPJ144 Instruction Manual preview
RPJ144
Brand: RCA Pages: 2
Galaxy Audio DSPOT DS-CP25 User Manual preview
DSPOT DS-CP25
Brand: Galaxy Audio Pages: 40
Waring WFP14SW Manual preview
WFP14SW
Brand: Waring Pages: 27
Quantum QL812SP Owner'S Manual preview
QL812SP
Brand: Quantum Pages: 32
Hamilton Beach 840083100 Use & Care Manual preview
840083100
Brand: Hamilton Beach Pages: 11
Kasanova SKN000001NOC Instruction Manual preview
SKN000001NOC
Brand: Kasanova Pages: 32
Vdwall LVP608 User Manual preview
LVP608
Brand: Vdwall Pages: 37
decakila KUMG002W Manual preview
KUMG002W
Brand: decakila Pages: 10
Dynamic Projection Mirror Head MH14 Manual preview
Mirror Head MH14
Brand: Dynamic Projection Pages: 37

Brands by name

Popular brands

Load more brands