Freescale Semiconductor Symphony DSP56724 Reference Manual Download Page 71

Page: 71 / 436

DSP56300 Platform

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

Freescale Semiconductor

4-3

barrel shifter, 24-bit addressing, an instruction patch module and direct memory access (DMA).
DSP56300 core features include:

•

DSP56300 modular chassis

•

250 million instructions per second (MIPS) with a 150 MHz clock with 1.2 V internal logic supply

•

Object code-compatible with DSP56000 core

•

Data ALU with 24

24 bit multiplier-accumulator and 56-bit barrel shifter plus support for 16-bit

arithmetic

•

Program control with support for position-independent code and instruction patches

•

8-channel DMA controller

•

Support for internal address-tracing plus OnCE for hardware/software debugging

•

STOP and WAIT low-power standby modes

4.3

DSP56300 Block Descriptions

The DSP56300 core provides five main functional blocks:

•

Data arithmetic logic unit (Data ALU)

•

Address generation unit (AGU)

•

Program control unit (PCU)

•

Internal Data Bus Switch

•

OnCE module

DSP56300 core features are described fully in the DSP56300 Family Manual.

4.3.1

Data ALU

The Data ALU performs all the arithmetic and logical operations on data operands in the DSP56300 core.
Data ALU features include:

•

Fully pipelined 24-bit

24-bit parallel multiplier-accumulator (MAC)

•

Bit field unit, comprising a 56-bit parallel barrel shifter (fast shift and normalization, bit stream
generation and parsing)

•

Conditional ALU instructions

•

24-bit or 16-bit arithmetic support under software control

•

Four 24-bit input general purpose registers: X1, X0, Y1 and Y0

•

Six Data ALU registers (A2, A1, A0, B2, B1 and B0), that are concatenated into two general
purpose 56-bit accumulators (A and B), plus accumulator shifters

•

Two data bus shifter/limiter circuits

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Search results

Summary of Contents for Symphony DSP56724

Reviews:

Freescale Semiconductor Symphony DSP56724, Reference Manual, Page: 71 / 436

Search results

Summary of Contents for Symphony DSP56724

Reviews: