manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual

The Freescale Semiconductor Symphony DSP56724 is a cutting-edge product that offers high-performance digital signal processing capabilities. Unlock its full potential with the comprehensive Reference Manual, available for free download from our website. Experience enhanced functionality and optimize your user experience with this invaluable manual.

Share
Download
background image

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

13-14

Freescale Semiconductor

 

Inter-Core Communication (ICC)

other core. When the other core services this interrupt, it reads its own read-only communication data 
register (ICDR4) to obtain the data from the core that produces the interrupt. This reading operation will 
clear the IF bit and set the ACK bit of the other core’s ICAR3 register, and an acknowledge interrupt is 
generated to indicate the serviced core that the interrupt has been serviced. The ACK bit can be cleared by 
writing 1 to the RACK bit of ICAR3 register.

For the core that generates the interrupt, the IE bit is readable and writable, but the IF bit is read-only. For 
the core that services the interrupt, IF and IE are read-only register bits.

For the core that generates the maskable interrupt, the RACK bit is read-writable and the ACK bit is 
read-only. For the core that services the maskable interrupt, RACK and ACK are both read-only bits.

13.3.2

Inter-Core Non-Maskable Interrupts

The ICC non-maskable interrupt operation is shown in 

Figure 13-16

.

Figure 13-16. Non-Maskable Interrupts

When one DSP core needs to generate a non-maskable interrupt to the other core, that core writes a datum 
to the ICDR1 data register. However, the data can be written to this register and the IF bit can only be set 
when DRE is 1, which indicates that the data register is empty. So the DRE bit must be polled before 
writing a datum to the ICDR1 data register. When the core writes a datum successfully into the ICDR1 
register, the DRE bit is cleared to indicate that the ICDR1 register is full, and the other core can now read 
this data correctly using its interrupt service routine. After the other core has read the communication data 
via its read-only ICDR2 register, the DRE bit will be set to indicate that the ICDR1 register is empty again.

The IF bit of the inter-core non-maskable interrupt control register (ICCR1) is not cleared by writing 1 to 
it or by the other core’s reading of the ICDR1 register. The IF bit of the ICCR1 register is automatically 
cleared by the hardware when the other core has serviced this non-maskable interrupt.

One Core 

writes

 

ICDR1

Other Core 

reads

 

Set IF bit

DRE == 1

Clear 

DRE

ICCR1

DRE

IF

DRE == 0

NMI to the 

other Core

Set DRE

Note: IF bit is 
cleared 
automatically by 
hardware.

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Symphony DSP56724

Sinbo SMX 2750 Instruction Manual preview
SMX 2750
Brand: Sinbo Pages: 42
Ninja PROFESSIONAL XL NF700 Series Quick Start Manual preview
PROFESSIONAL XL NF700 Series
Brand: Ninja Pages: 5
Krups Prep&Cook Instructions Manual preview
Prep&Cook
Brand: Krups Pages: 64
Tesla Delight FC510BWS User Manual preview
Delight FC510BWS
Brand: Tesla Pages: 40
GE 169141 User Manual preview
169141
Brand: GE Pages: 12
GE 840084000 Manual preview
840084000
Brand: GE Pages: 36
GE 840092600 User Manual preview
840092600
Brand: GE Pages: 36
GE G8P0AASSPSS Owner'S Manual preview
G8P0AASSPSS
Brand: GE Pages: 42
GE 169203 Instruction Manual preview
169203
Brand: GE Pages: 27
GE 840074400 User Manual preview
840074400
Brand: GE Pages: 36
GE FP1/4200 Use And Care Book Manual preview
FP1/4200
Brand: GE Pages: 48
Barco R767302K Instructions Manual preview
R767302K
Brand: Barco Pages: 38
Rompa 14024 Manual preview
14024
Brand: Rompa Pages: 4
GABOR UPM-360 User Manual preview
UPM-360
Brand: GABOR Pages: 12
SIGNALCORE SC5520A Hardware Manual preview
SC5520A
Brand: SIGNALCORE Pages: 40
Fakir COCTAIL MAX Instruction Manual preview
COCTAIL MAX
Brand: Fakir Pages: 20
Hamilton Beach 70650 User Manual preview
70650
Brand: Hamilton Beach Pages: 36
Hamilton Beach 36532 Use & Care Manual preview
36532
Brand: Hamilton Beach Pages: 56

Brands by name

Popular brands

Load more brands