manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual, Page: 83 / 436

Share
Download
Freescale Semiconductor Symphony DSP56724 Reference Manual Download Page 83

Core Configuration

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

Freescale Semiconductor

5-9

 

5.5

Interrupt Priority Registers

There are two PIC blocks in the DSP56724/DSP56725 device, with one PIC block for each DSP core. The 
PIC has also been enhanced to support additional DMA and peripheral interrupts. Two additional registers 
(IPR-C1, IPR-P1) have been added to the PIC to allow an additional 12 DMA interrupts and an additional 
12 peripheral interrupts. 

•

IPR-C is dedicated for DSP56724/DSP56725: 4 external interrupts and the first 6 DMA channels 
interrupts.

•

IPR-P is dedicated for DSP56724/DSP56725: 12 peripheral interrupt requests. 

•

IPR-C1 is dedicated for an additional 12 DMA channels interrupts; only 2 additional DMA 
channels are used in the DSP56724/DSP56725. 

•

IPR-P1 is dedicated for an additional 12 peripheral interrupt sources; only parts of the additional 
interrupts are used in the DSP56724/DSP56725.

The Interrupt Priority registers are shown in 

Figure 5-1

 through 

Figure 5-8

. The Interrupt Priority Level 

bits are defined in 

Table 5-8 

and

 Table 5-9. 

The interrupt priorities are shown in 

Table 5-10.

 The interrupt 

vectors are shown in 

Table 5-11

.

Table 5-8. Peripherals and DMA Interrupt Priority Level Bits

IPL bits

Interrupts Enabled

Interrupt Priority Level

(x)xxL1

(x)xxL0

0

0

No

—

1

Yes

0

1

0

Yes

1

1

Yes

2

Table 5-9. External Interrupts Priority Level Bits

IPL bits

Interrupts Enabled

Interrupt Priority Level

Interrupt Trigger Mode

IxL2

IxL1

IxL0

0

0

0

No

—

Level Triggered

1

Yes

0

1

0

Yes

1

1

Yes

2

1

0

0

No

—

Negative Edge Triggered

1

Yes

0

1

0

Yes

1

1

Yes

2

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments