manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual, Page: 72 / 436

Share
Download
Freescale Semiconductor Symphony DSP56724 Reference Manual Download Page 72

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

4-4

Freescale Semiconductor

 

DSP56300 Platform

4.3.1.1

Data ALU Registers

The Data ALU registers can be read or written over the X memory data bus (XDB) and the Y memory data 
bus (YDB), as 24- or 48-bit operands (or as 16- or 32-bit operands in 16-bit arithmetic mode). The source 
operands for the Data ALU, which can be 24, 48, or 56 bits (16, 32, or 40 bits in 16-bit arithmetic mode), 
always originate from Data ALU registers. The results of all Data ALU operations are stored in an 
accumulator.

All the Data ALU operations are performed in two clock cycles (in pipeline fashion) so that a new 
instruction can be initiated on every clock, yielding an effective execution rate of one instruction per clock 
cycle. The destination of every arithmetic operation can be used as a source operand for the immediately 
following arithmetic operation without a time penalty (without a pipeline stall).

4.3.1.2

Multiplier-Accumulator (MAC)

The MAC unit comprises the main arithmetic processing unit of the DSP56300 core and performs all of 
the calculations on data operands. For arithmetic instructions, the MAC accepts as many as three input 
operands and outputs one 56-bit result with the following form: Extension:Most Significant Product:Least 
Significant Product (EXT:MSP:LSP). 

The multiplier executes 24-bit 

×

 24-bit, parallel, fractional multiplies, between two’s-complement signed, 

unsigned, or mixed operands. The 48-bit product is right-justified and added to the 56-bit contents of either 
the A or B accumulator. A 56-bit result can be stored as a 24-bit operand. The LSP can either be truncated 
or rounded into the MSP. Rounding is performed if specified. 

4.3.2

Address Generation Unit (AGU)

The Address Generation Unit performs effective address calculations using integer arithmetic necessary 
to address data operands in memory, and contains the registers used to generate the addresses. The AGU 
implements four types of arithmetic (linear, modulo, multiple wrap-around modulo, reverse-carry), and 
operates in parallel with other chip resources to minimize address-generation overhead.

The AGU is divided into two halves, each with its own Address ALU. Each Address ALU has four sets of 
register triplets. Each register triplet is composed of an address register, an offset register and a modifier 
register. The two Address ALUs are identical. Each Address ALU contains a full 24-bit adder (called an 
offset adder). 

A second full adder (called a modulo adder) adds the summed result of the first full adder to a modulo 
value that is stored in its respective modifier register. A third full adder (called a reverse-carry adder) is 
also provided. 

The offset adder and the reverse-carry adder are in parallel and share common inputs. The only difference 
between the offset and reverse-carry adders is that the carry propagates in opposite directions. Test logic 
determines which of the three summed results of the full adders is output.

Each Address ALU can update one address register (from its respective address register file) during one 
instruction cycle. The contents of the associated modifier register specifies the type of arithmetic to be used 
in the address register update calculation. The modifier value is decoded in the Address ALU.

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments