manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual

The Freescale Semiconductor Symphony DSP56724 is a cutting-edge product that offers high-performance digital signal processing capabilities. Unlock its full potential with the comprehensive Reference Manual, available for free download from our website. Experience enhanced functionality and optimize your user experience with this invaluable manual.

Share
Download
background image

S/PDIF—Sony/Philips Digital Interface

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

Freescale Semiconductor

18-9

 

18.2.5

S/PDIF Reception Registers

The S/PDIF reception registers include:

•

Audio data reception registers: SPDIFRcvLeft (SRL), SPDIFRcvRight (SRR)

•

Channel status reception registers: SPDIFRxCChannel_h (SRCSH), SPDIFRxCChannel_l 
(SRCSL)

•

User bits reception registers: UchannelRcv (SRU), QchannelRcv (SRQ)

Table 18-6. Interrupt Register Field Descriptions

Bit

Field

Description

23–21

Reserved

For InterruptStat/Clear, return zeros when read. 
For InterruptEn, bit 23 also reads zero.

20

Lock

S/PDIF receiver’s DPLL is locked.

19

TxUnOv

S/PDIF transmit FIFO is under/overrun.

18

TxResyn

S/PDIF transmit FIFO resync.

17

CNew

S/PDIF receive change in value of control channel.

16

ValNoGood

S/PDIF validity flag is no good.

15

SymErr

S/PDIF receiver found illegal symbol.

14

BitErr

S/PDIF receiver found parity bit error.

13–11

Reserved

Return zeros when read.

10

URxFul

UChannel receive register is full.
The URxFul bit can’t be cleared using the IntClear register. 
To clear the URxFul bit, read from U RCV register.

9

URxOv

UChannel receive register is overrun.

8

QRxFul

QChannel receive register is full. 
The QRxFul bit can’t be cleared using the IntClear register. 
To clear the QRxFul bit, read from the Q RCV register.

7

QRxOv

QChannel receive register is overrun.

6

UQSync

U/Q Channel sync is found.

5

UQErr

U/Q Channel framing error.

4

PdirUnOv

Processor data input underrun/overrun occurred.

3

PdirResyn

Processor data input resync.

2

LockLoss

S/PDIF receiver loss of lock has occurred.

1

TxEm

S/PDIF transmit FIFO is empty.
The TxEm bit can’t be cleared using the IntClear register. 
To clear the TxEm bit, write to the TX fifo.

0

PdirFul

Processor data input is full.
The PdirFul bit can’t be cleared using the IntClear register. 
To clear the PdirFul bit, read from the PDIR FIFO.

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Symphony DSP56724

Samsung Flip WM55H Quick Setup Manual preview
Flip WM55H
Brand: Samsung Pages: 2
Vdwall LVP605 User Manual preview
LVP605
Brand: Vdwall Pages: 29
KTMAII CY-329 Instruction Manual preview
CY-329
Brand: KTMAII Pages: 11
Hamilton Beach Big Mouth 70590CR User Manual preview
Big Mouth 70590CR
Brand: Hamilton Beach Pages: 36
Lebensstil Kollektion LKCB-4112SS Instruction Manual preview
LKCB-4112SS
Brand: Lebensstil Kollektion Pages: 8
Morris S1528CH Manual preview
S1528CH
Brand: Morris Pages: 6
Kramer VIA-GO Quick Start Manual preview
VIA-GO
Brand: Kramer Pages: 4
Panasonic PressIT TY-WP2B1 Operating Instructions Manual preview
PressIT TY-WP2B1
Brand: Panasonic Pages: 49
WAGNER WiGA35 Quick Installation Manual preview
WiGA35
Brand: WAGNER Pages: 7
Fakir Atomic User Manual preview
Atomic
Brand: Fakir Pages: 52
PDR UPM51 Product Manual preview
UPM51
Brand: PDR Pages: 5
GINNY’S 762050 User Manual preview
762050
Brand: GINNY’S Pages: 16
Kogan KA10FDPRWSA User Manual preview
KA10FDPRWSA
Brand: Kogan Pages: 12
Cook's Companion CC500STKD Instruction Manual preview
CC500STKD
Brand: Cook's Companion Pages: 8
Varimixer Bowl Scraper 224 Specifications preview
Bowl Scraper 224
Brand: Varimixer Pages: 1
Johnson Crema Instructions For Use Manual preview
Crema
Brand: Johnson Pages: 20
3M HE100 Installation Instructions preview
HE100
Brand: 3M Pages: 4
Marta MT-1565 User Manual preview
MT-1565
Brand: Marta Pages: 10

Brands by name

Popular brands

Load more brands