manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual, Page: 358 / 436

Share
Download
Freescale Semiconductor Symphony DSP56724 Reference Manual Download Page 358

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

21-24

Freescale Semiconductor

 

External Memory Controller (EMC)

21.3.2.5

Memory Refresh Timer Prescaler Register (MRTPR)

The refresh timer prescaler register is used to divide the system clock to provide the SDRAM and UPM 
refresh timers clock.

13–10

WLFx

Write loop field. Determines the number of times a loop defined in the UPMx will be executed for a 
burst- or single-beat write pattern.
0000 16
0001 1
0010 2
0011 3
...
1110 14
1111 15

9–6

TLFx

Refresh loop field. Determines the number of times a loop defined in the UPMx will be executed for a 
refresh service pattern.
0000 16
0001 1
0010 2
0011 3
...
1110 14
1111 15

5–0

MAD

Machine address. RAM address pointer for the command executed. Each time that the UPM is 
accessed and the OP field is set to WRITE or READ, this field is incremented by 1. Address range is 
64 words per UPMx.

Table 21-29. Memory Refresh Timer Prescaler Register

MRTPR

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

X: 0xFF_FE43

R

PTP

W

R

PTP

W

Reset

0x00_0000

Table 21-30. MRTPR Field Descriptions

Bits

Name

Description

23–16

—

Reserved

15–8

PTP

Refresh timers prescaler. Determines the period of the refresh timers input clock. The system clock is 
divided by PTP except when the value is 00000_0000, which represents the maximum divider of 256.

Table 21-28. M

x

MRL Field Descriptions (Continued)

Bits

Name

Description

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments