manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual, Page: 205 / 436

Share
Download
Freescale Semiconductor Symphony DSP56724 Reference Manual Download Page 205

Symphony DSP56724/DSP56725 Multi-Core Audio Processors Reference Manual, Rev. 0

Freescale Semiconductor

11-1

 

Chapter 11  
Triple Timer Module (TEC, TEC_1)

11.1

Introduction

In the DSP56724/DSP56725, there are two internal triple timer modules. Core-0 uses TEC and Core-1 
uses TEC_1. In this chapter, only the TEC block is described in detail.

11.1.1

Overview

The timer module contains a common 21-bit prescaler and three independent and identical 
general-purpose, 24-bit timer/event counters, each with its own register set. Each of the timers has the 
following capabilities:

•

Uses internal or external clocking.

•

Interrupts the DSP Core after a specified number of events (clocks), or signals an external device 
after counting internal events.

•

Triggers DMA transfers after a specified number of events (clocks) occurs.

11.1.2

Triple Timer Module Block Diagram

Figure 11-1

 shows a block diagram of the triple timer module. This module includes a 24-bit Timer 

Prescaler Load Register (TPLR), a 24-bit Timer Prescaler Count Register (TPCR), and three timers. Each 
timer can use the prescaler clock as its clock source.

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments