![background image](http://html1.mh-extra.com/html/ducati/superbike-749r-2006/superbike-749r-2006_manual_2537770577.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Impianto elettrico
Electric system
sezione / section
P 7
63
749R
- M.Y. 2006 - edizione/edition 00
Funzione “Lap Time Memory”
La visualizzazione dei tempi sul giro
registrati è possibile quando la
motocicletta è ferma e il motore è
spento. Per entrare nella funzione
“Lap Time Memory” si deve tenere
premuto il tasto Dx mentre si porta la
chiave in posizione “ON”. Una volta
entrati nella modalità di visualizzazione
rilasciare il tasto: i dati memorizzati
si possono scorrere premendo il
tasto Sx.
Sul display LCD viene visualizzato il
numero associato al giro, il tempo
impiegato e la velocità massima
raggiunta durante il giro. Il contagiri
visualizza il regime motore massimo
raggiunto attivando eventualmente
le spie di cambiata con la consueta
logica.
Per resettare le rilevazioni
cronometriche, si deve premere il
tasto Dx per almeno 5 secondi.
L'uscita dalla funzione “Lap Time
Memory” avviene quando si porta la
chiave in posizione “OFF”.
Funzione tensione batteria
Il cruscotto misura la tensione
batteria visualizzandola nel riquadro
in basso a destra del display LCD.
Per leggere il valore, si deve premere
il tasto Dx fino alla comparsa della
scritta “VBATT”.
Gli estremi di visualizzazione sono 10
e 16 Volt: se il dato è compreso tra 10
e 12 Volt oppure tra 15 e 16 Volt,
l'indicazione lampeggia per segnalare
che la tensione della batteria è oltre
il campo ottimale di funzionamento.
Se la tensione rilevata è uguale o
inferiore a 9,9 Volt, compare la scritta
“LO” lampeggiante, mentre, se la
tensione è superiore o uguale a
16,1 Volt, compare la scritta “HI”
lampeggiante.
Durante la fase di trascinamento del
motore, la soglia per la comparsa
della scritta “LO” viene spostata a
8,5 volt in modo da tenere conto
dell'elevata caduta di tensione dovuta
all'assorbimento del motorino di
avviamento: in questo modo si
evitano falsi allarmi sulla lettura della
tensione batteria.
Quando il cruscotto rileva una
tensione batteria anomala, si porta
in modalità di allarme e provvede a
commutare la lettura del display
sulla funzione “VBATT”. Se durante
l'allarme viene premuto il pulsante
Dx, viene visualizzata la nuova
grandezza per 10 secondi per poi
tornare a visualizzare l'allarme.
Al termine dell'anomalia, il cruscotto
riprende la modalità di funzionamento
normale.
Lap Time Memory function
The recorded lap times can be
displayed when the motorcycle is
stationary and the engine is switched
off. To enter the Lap Time Memory
function, hold down the RH button
while turning the key to ON. Once the
display mode has been activated,
release the button: scroll through the
stored data by pressing the LH button.
The LCD will show the lap number,
time and maximum speed per lap.
The rev counter displays the
maximum engine speed; the gear
change lights will also operate
according to their usual logic.
To reset the recorded lap times,
hold down the RH button for more
than 5 seconds.
To exit the Lap Time Memory
function, turn the key to OFF.
Battery voltage
The instrument panel displays the
battery voltage in the box at the
bottom RH corner of the LCD.
To read the value, hold down the
RH button until the VBATT symbol
appears.
The display limits are 10 and 16 volts:
if the battery voltage is between
10 and 12 Volts or between 15 to
16 Volts, the value flashes to indicate
that the battery voltage is outside
the optimal operating range. If the
voltage is less than or equal to
9.9 Volts, a flashing LO symbol
appears, while if it is greater than
or equal to 16.1 Volts, a flashing HI
symbol appears.
When the engine is being started
with the starter motor, the LO
threshold is reduced to 8.5 Volts
to account for the voltage drop
occasioned by the starter motor itself:
this avoids misleading alarm warnings
on the battery voltage readout.
When the instrument panel reads an
anomalous battery voltage, it moves
to alarm mode and switches the
display automatically to the
VBATT indication. If the RH button is
pressed during the alarm condition,
the new reading is displayed for
10 seconds, after which the alarm is
again displayed. At the end of the
malfunction, the instrument panel
returns to normal operation.
`
STATO 1
STATUS 1
STATO 2
STATUS 2
STATO 3
STATUS 3
VISUALIZZAZIONE
" LO "
LAMPEGGIANTE /
"LO" FLASHING
VISUALIZZAZIONE
" HI "
LAMPEGGIANTE /
"HI" FLASHING
VISUALIZZAZIONE
LAMPEGGIANTE /
FLASHING
VISUALIZZAZIONE FISSO /
DISPLAYED
VISUALIZZAZIONE LAMPEGGIANTE /
FLASHING
0.0
9.9
10
12.1
12
14.9
15
16.1
16
VOLT
Summary of Contents for Superbike 749R 2006
