![background image](http://html1.mh-extra.com/html/ducati/superbike-749r-2006/superbike-749r-2006_manual_2537770244.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Ruote – Sospensioni – Freni
Wheels – Suspensions – Brakes
sezione / section
G 8
44
749R
- M.Y. 2006 - edizione/edition 00
Rimontaggio pignone
catena
Prima del montaggio, verificare che
sull’albero secondario sia presente il
distanziale (
16
).
Verificare che la calettatura dell’albero
secondario e quella del pignone
risultino in perfette condizioni.
Montare il pignone motore (3) e
installare la rosetta di sicurezza (
2
).
Bloccare il dado (1) alla coppia di
serraggio prescritta (Sez. C 3).
Montare la catena e richiuderla
utilizzando l'attrezzo cod.
88713.1344
,
usato per aprire la catena.
L'attrezzo è composto da un
contenitore (A), da un punzone (B), da
un corpo (C), da due chiavi (D) ed (E)
e un contenitore piastrino (F).
Collegare le due estremità della catena
con la maglia esterna e inserire
manualmente la piastrina sui perni.
Attenzione
Lubrificare abbondantemente
i perni ed evitate il più possibile di
toccarli con le mani.
Posizionare il contenitore (A) in
corrispondenza della maglia esterna.
Montare il punzone (B) sul corpo (C) e
il contenitore piastrina (F).
Inserire il corpo (C) nel contenitore (A)
che trattiene la catena in posizione.
Girare a mano il bullone (G) fino a
quando il contenitore piastrina (F) sia
in appoggio alla piastrina stessa.
Con l'ausilio delle chiavi (D) e (E)
girare il bullone (G) in senso orario fino
a quando il perno della catena viene in
contatto con il contenitore (F).
Togliere dall'attrezzo il contenitore (A).
Girare il bullone (G) a mano fino a
quando il punzone (B) sia a contatto
con il perno da ribadire e controllare
che questi siano in asse.
Utilizzando le chiavi (D) e (E) girare il
bullone in senso orario fino a quando
il punzone (B) sia in appoggio sulla
piastrina della catena.
Al fine di completare la ribaditura,
spostarsi con tutto l'attrezzo nel
secondo perno e ripetere le
procedure citate.
Attenzione
Controllare scrupolosamente i
due perni ribaditi: la figura riporta il
perno ribadito correttamente.
Eseguire il tensionamento della
catena (Sez. D 4).
Posizionare il coperchio pignone (6)
serrando le viti (5) alla coppia
prescritta (Sez. C 3).
Refitting the front
sprocket
Before fitting the front sprocket,
check that the spacer (
16
) is installed
on the gearbox output shaft.
Check that the splines of the gearbox
output shaft and the sprocket are in
perfect condition.
Fit the front sprocket (3) and install
the safety washer (
2
).
Tighten the nut (1) to the specified
torque (Sect. C 3).
Fit the chain and join the links using the
same service tool part no.
88713.1344
that was used to split the chain.
The tool is composed of a holder (A),
punch (B), body (C) and two
wrenches (D) and (E) and link plate
holder (F).
Connect the two halves of the chain
with the external link and manually fit
the plate onto the pins.
Warning
Lubricate the pins abundantly;
try to avoid touching them with your
hands.
Fit the holder (A) onto the external link.
Fit the punch (B) into the body (C) and
the plate holder (F).
Fit the body (C) onto the holder (A)
which holds the chain in position.
Manually turn the bolt (G) until the
plate holder (F) is seated against the
plate itself.
Use wrenches (D) and (E) to turn the
bolt (G) clockwise until the chain pin is
in contact with the holder (F).
Remove the holder (A) from the tool.
Manually turn the bolt (G) until the
punch (B) locates against the pin,
taking care that they are aligned with
each other.
Use wrenches (D) and (E) to turn the
bolt clockwise until the punch (B) is
seated against the chain plate.
To complete reassembly, repeat the
entire procedure with the second pin.
Warning
Carefully check the two pins:
the figure shows the correct result
of the procedure.
Adjust the chain tension (Sect. D 4).
Fit the sprocket cover (6) and tighten
the screws (5) to the specified torque
(Sect. C 3).
3
1
88713.1344
A
F
B
C
G
6
5
SI
YES
NO
NO
NO
NO
NO
NO
E
E
D
D
G
Summary of Contents for Superbike 749R 2006
