![background image](http://html1.mh-extra.com/html/ducati/superbike-749r-2006/superbike-749r-2006_manual_2537770596.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Impianto elettrico
Electric system
sezione / section
P 9
82
749R
- M.Y. 2006 - edizione/edition 00
essere misurata. (La tensione
continua è indicata con il simbolo = e
quella alternata con il simbolo ~).
La misura di correnti
Le misure delle correnti devono essere
effettuate collegando sempre i
terminali del multimetro in serie
all'elemento alimentato elettricamente
(ad esempio occorre staccare un filo
che alimenta una lampadina e
collegare alla estremità del filo stesso
un terminale del multimetro e l'altro
terminale alla lampadina. Accendendo
il commutatore delle luci la lampadina
si illuminerà normalmente e lo
strumento indicherà la corrente
assorbita e cioè quella che circola nel
filo). Attenzione: i collegamenti in serie
vanno effettuati e rimossi sempre
quando non c'è tensione. Non si deve
mai effettuare od eliminare un
collegamento in serie quando un
dispositivo è alimentato. Assicurarsi
sempre che il collegamento in serie dei
terminali del tester fatto sul dispositivo
elettrico, sia realizzato in modo sicuro e
che perciò non possa interrompersi in
modo accidentale.
La misura di resistenze e di
continuità elettrica
Le misure di resistenze devono
essere effettuate solo quando
l'elemento elettrico o la sezione
dell'impianto non è alimentato ed è
isolato dall'impianto elettrico
principale (cioè non collegato
all'impianto elettrico principale).
Queste misure possono essere
utilizzate per verificare la resistenza di
alcuni sensori. Ad esempio dopo aver
scollegato la connessione elettrica
del sensore dei giri/fase dell'impianto
di accensione - iniezione (affacciato
all'ingranaggio di comando dell'albero
della distribuzione), è possibile
verificare la sua resistenza interna,
collegando il multimentro ai suoi
terminali. In questo modo si verifica
se l'avvolgimento interno al sensore è
interrotto (caso in cui la resistenza è
infinita). La misura della resistenza
può essere utilizzata anche per
controllare la continuità di tratti
dell'impianto elettrico o di interruttori
e relè. Per verificare ad esempio
l'integrità di una sezione di impianto
elettrico tra due connessioni, occorre
scollegare le connessioni stesse,
collegare i terminali del multimetro
alle due estremità del cavo elettrico e
verificare il valore di resistenza
indicato. Se questo valore è prossimo
allo zero (inferiore a circa 0,3 ohm)
allora il cavo non è interrotto.
measure. (continuous voltage is
shown by the symbol = while
alternating voltage is denoted by ~).
Current measurement
Current measurements must be
made by connecting the multimeter
terminals in series with the electrically
powered device (e.g. disconnect one
of the wires feeding power to a light
bulb and connect one terminal of the
multimeter to the free end of wire and
the other terminal to the light bulb.
When the lights switch is set to On,
the bulb will illuminate normally and
the tester will show the absorbed
current, i.e. the amount of current
passing through the wire). Warning:
connections in series must be made
and removed only when the power is
switched off. Never attempt to make
or break a series connection when a
device is powered. Always make sure
that the series connection of the
tester terminals on the electrical
device is made in a safe manner in
such a way that it cannot be broken
accidentally.
Measurement of resistance
values and electrical continuity
Resistance measurements must be
taken only when the electrical device
or section of the circuit is not
powered and isolated from the main
electrical system (i.e. not connected
to the main electrical system).
These measurements can be utilised
to check the resistance value across
several sensors. For example, after
disconnecting the electrical wiring
to the rpm/ignition - injection system
timing sensor (in front of the
camshaft drive gear) the relative
internal resistance can be checked
by connecting a multimeter to its
terminals. This makes it possible to
check the electrical continuity of the
winding inside the sensor (a reading
of infinite resistance indicates that
the winding is interrupted).
Resistance measurement can also be
used to check the continuity of
sections of the electrical circuit or
relay type switches. For example, to
check the condition of a section of the
electrical circuit between two
connections, disconnect the
connections and connect the
terminals of the multimeter to the
ends of the electrical cable in
question to check that the specified
resistance value is present. If this
value is close to zero (i.e. lower than
approximately 0.3 ohm) this means
that the cable is not interrupted.
Summary of Contents for Superbike 749R 2006
