Appendix A Specifications
A-3
General Specifications
Operation
Setting
Signal
Keypad
Set by RUN and STOP
External Signal
2 wires/3 wires (MI1, MI2, MI3), JOG operation, RS-485 serial interface
(MODBUS), programmable logic controller
Multi-function Input Signal
Multi-step selection 0 to 15, Jog, accel/decel inhibit, 2 accel/decel switches,
counter, external Base Block, ACI/AVI selections, driver reset, UP/DOWN
key settings, NPN/PNP input selection
Multi-function Output Indication
AC drive operating, frequency attained, zero speed, Base Block, fault
indication, overheat alarm, emergency stop and status selections of input
terminals
Analog Output Signal
Output frequency/current
Alarm Output Contact
Contact will be On when drive malfunctions (1 Form C/change-over contact
and 1 open collector output) for standard type)
Operation Functions
Built-in PLC(NOT for CANopen models), AVR, accel/decel S-Curve, over-
voltage/over-current stall prevention, 5 fault records, reverse inhibition,
momentary power loss restart, DC brake, auto torque/slip compensation,
auto tuning, adjustable carrier frequency, output frequency limits, parameter
lock/reset, vector control, PID control, external counter, MODBUS
communication, abnormal reset, abnormal re-start, power-saving, fan control,
sleep/wake frequency, 1st/2nd frequency source selections, 1st/2nd
frequency source combination, NPN/PNP selection, parameters for motor 0
to motor 3, DEB and OOB (Out Of Balance Detection)(for washing machine)
Protection Functions
Over voltage, over current, under voltage, external fault, overload, ground
fault, overheating, electronic thermal, IGBT short circuit, PTC, instantly stop
and then reboot(up to 20 sec by setting parameter)
Display Keypad (optional)
6-key, 7-segment LED with 4-digit, 5 status LEDs, master frequency, output
frequency, output current, custom units, parameter values for setup and lock,
faults, RUN, STOP, RESET, FWD/REV, PLC
Built-in Brake Chopper
VFD002E11T/21T/23T, VFD004E11T/21T/23T/43T, VFD007E21T/23T/43T,
VFD015E23T/43T, VFD007E11A/11C, VFD015E21A/21C,
VFD022E21A/21C/23A/23C/43A/43C, VFD037E23A/23C/43A/43C,
VFD055E23A/23C/43A/43C, VFD075E23A/23C/43A/43C,
VFD110E23A/23C/43A/43C, VFD150E23A/23C/43A/43C,
VFD185E43A/43C, VFD220E43A/43C
Built-in EMI Filter
For 230V 1-phase and 460V 3-phase models.
Envi
ronm
en
tal
C
o
ndi
ti
ons
Enclosure Rating
IP20
Pollution Degree
2
Installation Location
Altitude 1,000 m or lower, keep from corrosive gasses, liquid and dust
Ambient Temperature
-10
o
C to 50
o
C (40
o
C for side-by-side mounting) Non-Condensing and not
frozen
Storage/ Transportation
Temperature
-20
o
C to 60
o
C
Ambient Humidity
Below 90% RH (non-condensing)
Vibration
10Hz
≦
f
≦
57Hz Fix Amplitude:0.075mm
57Hz
≦
f
≦
150Hz Fix Acceleration: 1G
(According to IEC 60068-2-6)
Approvals
