![background image](http://html1.mh-extra.com/html/conair/trueblend-sb-4/trueblend-sb-4_user-manual_2649035126.webp)
4 - 8 8
l O p e r a t i o n
S e t u p S c r e e n s
( c o n t i n u e d )
Remote Loading
The blender can perform load sequencing for loader bodies located on remote blenders. The
blenders must be connected via standard Ethernet wiring practices. The following procedure
outlines the process for setting up this type of connection.
1
The Node ID for each blender must be properly set.
This identifies each blender on
the loading network.
2
From the <Home> screen for the blender system without the pump, press [More…]
– [Setup] – [Network] – [IP Address] - [Advanced] set the NodeID to a value of 1.
3
For the blender system without the pump, set the IP address (10.1.42.1) and the
Subnet mask to (255.255.0.0).
Returning to the <Home> screen will reboot the system.
4
From the <Home> screen for the blender system with the pump, press [More…] –
[Setup] – [Network] – [IP Address] - [Advanced] set the NodeID to a value of 2.
5
For the blender system with the pump, set the IP address (10.1.42.2) and the Subnet
mask to (255.255.0.0).
Returning to the home screen will reboot the system.
6
Enable the self-loading feature on both blenders.
This requires unique license codes
for each system and the proper hardware installed. This will restart the touch-panels
when returning to the home page. From the <Home> screen press [More…] – [Setup] –
[System] – [Control]. For (Loading Enabled) select (Control) and enter the license code.
7
The self-loading feature should now be enabled, Ethernet addresses set,
and the
nodeID for both systems set. This can be verified on the <Setup> - <Network> - <Info>
screen and the <Setup> - <System> - <Control> screen for the self-loading enabling.
8
Physically connect both blenders to the same Ethernet network.
If the blenders are
connected directly together use a crossover cable. If using a switch or hub, then standard
Ethernet cables into the switch will work.
9
On the blender with the pump and NodeID set to a 2, enter [More…] – [Setup] –
[More…] – [Loader] – [System].
Set the number of loader bodies available on this
blender only.
10
Navigate to the Loader setup screen [More…] – [Setup] – [More…] – [Loader] –
[Control].
For each loader, check the blower address setting. They should all be set to 2
because that is the system with a nodeID of 2 and where the pump is located.
11
Press the [Blower] blower button to show the blower settings for blender with Node
ID 2.
Verify the blower address is set to a 2.
12
On the blender without the pump and NodeID set to a 1, enter [More…] – [Setup] –
[More…] – [Loader] – [System].
Set the number of loader bodies available on this
blender only.
13
Navigate to the Loader setup screen [More…] – [Setup] – [More…] – [Loader] –
[Control].
For each loader, check the blower address setting. They should all be set to 2
because that is the system with a nodeID of 2 and where the pump is located.
(Continued)
Summary of Contents for TrueBlend SB-4
