Atmel SAM9X25, Manual

Page: 496 / 1145

496
11054A–ATARM–27-Jul-11
SAM9X25
496
11054A–ATARM–27-Jul-11
SAM9X25
– v. Incrementing/decrementing or fixed address for source in SRC_INCR field.
– vi. Incrementing/decrementing or fixed address for destination DST_INCR field.
3. Write the starting destination address in the DMAC_DADDRx register for channel x.
Note: The values in the LLI.DMAC_DADDRx register location of each Linked List Item (LLI) in memory,
although fetched during an LLI fetch, are not used.
4. Write the channel configuration information into the DMAC_CFGx register for
channel x.
a. Designate the handshaking interface type (hardware or software) for the source
and destination peripherals. This is not required for memory. This step requires pro-
gramming the SRC_H2SEL/DST_H2SEL bits, respectively. Writing a ‘1’ activates
the hardware handshaking interface to handle source/destination requests for the
specific channel. Writing a ‘0’ activates the software handshaking interface to han-
dle source/destination requests.
b. If the hardware handshaking interface is activated for the source or destination
peripheral, assign handshaking interface to the source and destination peripherals.
This requires programming the SRC_PER and DST_PER bits, respectively.
5. Make sure that all LLI.DMAC_CTRLBx register locations of the LLI (except the last) are
set as shown in Row 2 of
Table 31-3 on page 479 , while the LLI.DMAC_CTRLBx regis-
ter of the last Linked List item must be set as described in Row 1 of Table 31-3 . Figure
31-5 on page 478 shows a Linked List example with two list items.
6. Make sure that the LLI.DMAC_DSCRx register locations of all LLIs in memory (except
the last) are non-zero and point to the next Linked List Item.
7. Make sure that the LLI.DMAC_SADDRx register location of all LLIs in memory point to
the start source buffer address proceeding that LLI fetch.
8. Make sure that the LLI.DMAC_CTRLAx.DONE field of the LLI.DMAC_CTRLAx register
locations of all LLIs in memory is cleared.
9. If source picture-in-picture is enabled (DMAC_CTRLBx.SPIP is enabled), program the
DMAC_SPIPx register for channel x.
10. If destination picture-in-picture is enabled (DMAC_CTRLBx.DPIP is enabled), program
the DMAC_DPIPx register for channel x.
11. Clear any pending interrupts on the channel from the previous DMAC transfer by read-
ing the interrupt status register.
12. Program the DMAC_CTRLAx, DMAC_CTRLBx and DMAC_CFGx registers according
to Row 2 as shown in Table 31-3 on page 479
13. Program the DMAC_DSCRx register with DMAC_DSCRx(0), the pointer to the first
Linked List item.
14. Finally, enable the channel by writing a ‘1’ to the DMAC_CHER.ENABLE[n] bit. The
transfer is performed. Make sure that bit 0 of the DMAC_EN register is enabled.
15. The DMAC fetches the first LLI from the location pointed to by DMAC_DSCRx(0).
Note: The LLI.DMAC_SADDRx, LLI.DMAC_DADDRx, LLI.DMAC_DSCRx and LLI.DMAC_CTRLA/Bx
registers are fetched. The LLI.DMAC_DADDRx register location of the LLI although fetched is not
used. The DMAC_DADDRx register in the DMAC remains unchanged.
16. Source and destination requests single and chunk DMAC transactions to transfer the
buffer of data (assuming non-memory peripherals). The DMAC acknowledges at the
completion of every transaction (chunk and single) in the buffer and carry out the buffer
transfer
17. Once the buffer of data is transferred, the DMAC_CTRLAx register is written out to sys-
tem memory at the same location and on the same layer (DMAC_DSCRx.DSCR_IF)
where it was originally fetched, that is, the location of the DMAC_CTRLAx register of