Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 178

background image

2-4

Excessive Weight Hazard

Use two or more people to move and
install washer.

Failure to do so can result in back or
other injury.

WARNING

INSTALLING THE WASHER

2. The shipping strap plug must be completely

removed from the washer for the self-level-
ing legs to be released. Save the shipping
strap for use in step 7.

Removing the shipping strap is necessary for
smooth operation. If the shipping strap is not
removed, the washer will make excessive noise.

1. Do not cut yellow strap. Pull yellow strap

firmly, until completely removed from
washer. There will be two cotter pins on the
end of the shipping strap when it is pulled
out of the washer. The electrical plug is
attached to this shipping strap.

To minimize a possible shock hazard, the cord
must be plugged into a mating 3-prong ground-
ing-type receptacle, which has been grounded
in accordance with National Electrical Code
(ANSI/NFPA 70), and all local and state codes.

If a mating outlet is not available, it is the
personal responsibility and obligation of the
customer to have a properly grounded 3-prong
outlet installed by a qualified electrician.

IMPORTANT:

Improper connection of the

equipment-grounding conductor can result in a
risk of electric shock. Do not modify the plug
provided with the appliance. If it will not fit the
outlet, have a proper outlet installed by a quali-
fied electrician.

3-Prong
Grounding
Plug

Power Supply
Cord

Ground
Prong

3-Prong Grounding-
Type Outlet

If codes permit and a separate ground wire is
used, it is recommended that a qualified elec-
trician determine that the ground path is ad-
equate.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not
sure the washer is properly grounded.

Do Not have a fuse in the neutral or ground
circuit.

A 120-volt, 60-Hz, AC-only, 15- or 20-ampere
fused electrical supply is required. (Time-
delay fuse or circuit breaker is recom-
mended.) It is recommended that a separate
circuit serving only this appliance be provided.

Grounding Instructions

For the safety of the customer, this washer
must be grounded. The washer is equipped
with a power supply cord that has a 3-prong
grounding plug.

«
...
16
17
18
19
20
...
»

Содержание ADVANTECH CAE2761K



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADVANTECH CAE2761K

Бренд: Labconco Страницы: 72

Бренд: Artusi Страницы: 46

WA422PRHD Series

Бренд: Samsung Страницы: 36

Бренд: NEFF Страницы: 29

Бренд: Fisher & Paykel Страницы: 5

Бренд: Gorlitz Страницы: 16

Бренд: HomeKing Страницы: 52

Бренд: Maytag Страницы: 27

Бренд: Kärcher Страницы: 20

Бренд: VALBERG Страницы: 92

Бренд: Baumatic Страницы: 36

Бренд: BALAY Страницы: 56

Бренд: Hitachi Страницы: 200

Бренд: Hotpoint Страницы: 16

Бренд: Miele Страницы: 84

Бренд: Miele Страницы: 2

Бренд: Miele Страницы: 92

WER 865 WPS Excellence

Бренд: Miele Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды