Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Страница: 131 / 178

6-3
TIME AND DATE CLOCK
The time and date are not set at the factory.
The electronic control uses a battery to run the
clock. If the wire harness at connector P2 is
unplugged, the battery is disconnected and the
time and date must be reset. The battery has a
life of approximately ten years.
ADDITIONAL INFORMATION
Additional information about the machine’s
performance, such as when a fill time was too
long or when the AC power was turned off, is
available when gathering data via the Palm

handheld. For more information on this fea-
ture, see ADVANTECH

Commercial Laundry
Products Software User’s Manual, # 8524743 .
DISPLAY
EXPLANATION
Service person placed machine out of service.
See
MANUAL OUT OF SERVICE
section.
Machine has been set to be unavailable for
customer use by means of one of the three owner
‘special’ prices. See SP 1, SP 2 and SP 3 (special
price) on page 6-4.
No money device is enabled during machine setup.
Please enable Card (SMART Card). See
OWNER
SETTINGS.
The setup may be requesting a coindrop. See
OWNER SETTINGS.
An error is occurring with the auxiliary device, such
as a Smart Card unit not plugged into connector of
control board. (The setting is enabled but no Smart
Card unit is installed.) See
OWNER SETTINGS.
Lid was not opened between end of cycle and next
spin. Run service routine to reset. See
SERVICE
ROUTINE
on page 6-1.
Off Codes
The display shows the word “OFF” to inform
the customer the machine is out of service. If
money is added to the machine, it will be lost.
Refer to the “Off Codes” table.
OWNER SETTINGS
1. Perform all steps under “Access Mode” on
page 6-1.
2. Push and release keypad position 1 (HOT).
3. Keypads are now re-mapped for navigating
the settings as follows:
4. When an item on the list is selected, the
current setting is displayed. To change a
setting, use the keypads as follows:
5. To accept the displayed setting, press key-
pad #6, and the program will return to the
OWNER SETTINGS menu.
6. After all changes to the OWNER SET-
TINGS are complete, press keypad #6 twice
to exit the program. The display returns to
the vend-price.
KEYPAD NAVIGATING OWNER SETTINGS
HOT
1 up
Move up to the preceding item on the list.
Refer to the
OWNER SETTINGS
table.
WARM
2 down
Move down to the next item on the list.
Refer to the
OWNER SETTINGS
table.
COLD
3
select
Select an item to view the current setting.
Refer to the
OWNER SETTINGS
table.
NORMAL
4
— no function
GENTLE
5
— no function
6
(hidden)
exit
Exit
OWNER SETTINGS
program. Display
returns to the cycle count.
KEYPAD CHANGING OWNER SETTINGS
HOT
1
(+)
increase
Increase the setting value. Push and hold the
keypad for fast increase. Refer to the
OWNER
SETTINGS
table.
WARM
2
(–)
decrease
Decrease the setting value. Push and hold the
keypad for fast decrease. Refer to the
OWNER
SETTINGS
table.
COLD
3
—
no function
NORMAL
4
— no function
GENTLE
5
— no function
6
(hidden)
accept
Accept the new setting value. Display returns
to
OWNER SETTINGS
list.
DISPLAY DESCRIPTION
Default
Setting Value
Range
CYCLE PRICE
—
$ dollars
0.75 0.00 to 100.00
CALENDAR YEAR
2000 2000 to 2030
CALENDAR DATE
— month and day
1.1
(Jan. 1)
1 to 12 months
1 to 31 days
TIME
—
24-hour clock
(hours.minutes)
0.00 0.00 to 23.59
Table Continued on the next page.
OWNER SETTINGS TABLE