Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 178

background image

2-13

The maximum length of an exhaust system
depends upon the type of vent used, the num-
ber of elbows, and the type of exhaust hood.
The maximum lengths for both rigid and flex-
ible venting is shown in the chart below.

For exhaust systems not covered by the ex-
haust length chart, see the Whirlpool Service
Manual: “Exhausting Whirlpool Dryers,” Part
No.

603197

, which is available from your Whirl-

pool parts distributor. Also refer to Section 8.

If a dryer is installed in a confined area, it must
be exhausted to the outside, and provision
made for enough air for combustion and venti-
lation. Check governing codes and ordinances.

A 4

″

(10.2 cm) outlet hood is preferred, how-

ever, a 2 1/2

″

(6.4 cm) outlet exhaust hood may

be used. A 2 1/2

″

(6.4 cm) outlet creates

greater backpressure than other hood types.
For permanent installation, a stationary ex-
haust system is required.

«
...
25
26
27
28
29
...
»

Содержание ADVANTECH CAE2761K



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADVANTECH CAE2761K

Бренд: GE Страницы: 2

Бренд: Kärcher Страницы: 8

Бренд: Daewoo Страницы: 17

Бренд: Daewoo Страницы: 16

Бренд: Danby Страницы: 42

Бренд: Danby Страницы: 11

Бренд: Danby Страницы: 10

Бренд: Maidaid Halcyon Страницы: 17

Бренд: Panasonic Страницы: 21

K 4.650 Jubilee

Бренд: Kärcher Страницы: 18

Бренд: Kärcher Страницы: 184

Бренд: Smeg Страницы: 10

Бренд: GE Страницы: 72

Бренд: ZANKER Страницы: 68

Бренд: Gaggenau Страницы: 52

Бренд: Hypro Страницы: 20

Бренд: Icecool Страницы: 112

Бренд: Dynex Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды