Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 60

Страница: 60 / 178

4-2

REMOVING THE CONSOLE COMPONENTS

Unplug washer or disconnect power.

Remove the two T-15 Torx screws from
the console.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Slide the console to the front of the unit
slightly, then rotate it back and place it in
the “service” position.

NOTE:

The Model CAE2792K is shown in this

console removal procedure. The Model
CAE2762K uses the same components, but
without the card reader.

T-15 Torx Screws

Console

To remove the ADVANTECH



control

board:

a) Disconnect the 6 board connectors at

P1, P2, P3, P4, P8, and P11.

b) Disconnect the green ground wire from

terminal P6.

c) Remove the six 5/16

″

hex-head screws

from the board and remove the board
from the unit.

To remove the display board:

a) Remove the ADVANTECH



control

board (see step 4).

b) Disconnect the connector from the dis-

play board at P1.

c) Unlatch the display board from the

holder and remove it.

Control Board And Display Board

(Below Control Board)

Card Reader

Screw (1 of 6)

P11

Ground Wire

ADVANTECH



Control Board

Display Board

Latch

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды