Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 178

background image

4-17

9.

Lift the cabinet slightly and tip it forward on
its front edges.

IMPORTANT:

The cabinet

will not stand on its own in the upright
position.

Side Rail

Alignment Tab

NOTE:

Tension can be added to the cabinet

clips to insure better frame-to-cabinet fit by
adjusting the clips. Apply pressure in the direc-
tion of the arrow while holding the clip in the
pliers. Another method is to install kit

#488495

.

NOTE:

You can remove the right and left side

panels of the cabinet, instead of removing the
complete cabinet assembly. However, you will
have to remove the front panel first.

REASSEMBLY NOTE:

When you reinstall the

cabinet,  make  sure  that  the  small  alignment
tabs at the front and rear of each side rail are
fully  upright,  as  shown  below,  and  not  bent
over.  Also  make  sure  that  the  side  rails  are
straight and not deformed, otherwise, the cabi-
net will not fit properly.

Damaged Bottom
Cabinet Flange

Properly Aligned
Bottom Cabinet Flange

Plastic Lock

«
...
73
74
75
76
77
...
»

Содержание ADVANTECH CAE2761K



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADVANTECH CAE2761K

Бренд: Belling Страницы: 18

Бренд: Kärcher Страницы: 62

Бренд: Hanseatic Страницы: 72

Бренд: Campbell Hausfeld Страницы: 20

Бренд: Scandium Страницы: 40

Бренд: Kranzle Страницы: 18

Бренд: Smeg Страницы: 27

Бренд: ETNA Страницы: 72

Бренд: Gerni Страницы: 21

Бренд: GE Страницы: 48

Aqualtis AQXXL 149 PI

Бренд: Hotpoint Страницы: 16

Бренд: Esatto Страницы: 28

Бренд: Baumatic Страницы: 44

Бренд: GE Страницы: 28

WA85J571 Series

Бренд: Samsung Страницы: 88

Бренд: Electrolux Страницы: 18

Бренд: Electrolux Страницы: 20

Бренд: Electrolux Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды