Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 20

Страница: 20 / 178

2-6

13. Screw the feet into the correct holes at the

front corner of the washer until the nuts
touch the washer.

NOTE:

Do not tighten the

nuts until the washer is level, step 17.

14. Tilt washer backward and remove the wood

block. Gently lower washer to floor. Move
washer to its permanent location. Remove
cardboard or hardboard from under washer.

15. Tilt washer forward raising back legs 1

″

(2.5 cm) off of floor. To adjust rear leveling
legs, gently lower washer to floor.

9. Before attaching water inlet hoses, run water

through both faucets into a bucket. This will
get rid of particles in water lines that might
clog hoses. Mark which is the hot water
faucet.

10. Attach bottom hose (inlet marked “H”) to

hot water faucet. Attach top (inlet marked
“C”) to cold water faucet. Tighten coupling
to faucet by hand, then use pliers to make
final two-thirds turn.

11. Prop up the front of the washer about 4

″

(10.2 cm) with a wood block, or similar
object. The block needs to support the
weight of the washer.

12. Screw the locknut onto each foot to within

″

(2.5 cm) of the base.

2.5 cm
(1

″

)

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды