Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 94

Страница: 94 / 178

4-36

d) Disconnect the two P4 connectors for

the upper and lower dryers from the
ADVANTECH



control boards and re-

move the console from the unit.

P4 Connectors

ADVANTECH



Control Boards

To remove the cycle selector switches
from the console:

a) Remove the console (see step 3).
b) Disconnect the selector switch wires.

NOTE:

A switch wiring color-code

sticker is shown on the bracket.

c) Remove the four bracket screws and lift

the bracket and selector switches from
the console.

Upper Dryer Selector Switch

Lower Dryer Selector Switch

Bracket W/4 Screws

To remove the lock from the console:

a) Remove the console (see step 3).
b) Remove the 7/16

″

hex-nut from the

lock and remove the lockwasher, lock-
ing cam, 2 wave washers, and lock stop
(see the illustration below).

c) Remove the 7/8

″

hex-nut from the lock

and remove the lock from the console.

Console Lock

Lock

7/8

″

Hex-Nut

Lock Stop

Locking Cam

Wave Washers 2

7/16

″

Hex-Nut

Lockwasher

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды