Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 91

Страница: 91 / 178

4-33

REMOVING THE CABINET

c) Slide the top forward to release if from

the two front side panel clips, and re-
move the top from the unit.

Side

Panel

Clips

Continued on the next page.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

3 Screws

Unplug dryer or disconnect power.

Turn off gas supply to dryer.

To remove the dryer top:

a) Slide the console to the front of the unit

slightly, then rotate it back and place it
in the service position.

b) Remove the three rear hex-head screws

from the top.

Hex-Screws

Torx Screws W/Flat Washers

Front Panel

To remove the lower service access
panel,

use a putty knife, and pry down on

the upper retaining clips while pulling for-
ward on the lower service access panel,
and remove the panel.

Clip

Lower Service

Access Panel

o remove the front panel:

a) Remove the lower service access panel

(see step 4).

b) Remove the two bottom hex-head

screws and the two T-15 Torx screws
and flat washers from the top of the
front panel.

Pry

Down

Clip

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды