Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 89

Страница: 89 / 178

4-31

To remove the coindrop assembly:

a) From inside the open access panel of

the metercase, remove the screws or
hex-bolts from the back of the coindrop
assembly.

b) Position the console to its service posi-

tion (see page 4-26 for the procedure).

c) Disconnect the connector(s) at P10 /

COIN 1 (& P12 / COIN 2) on the
ADVANTECH



control board.

To remove the coinbox switch:

a) Unlock and remove the service access

panel and the coinbox from the meter-
case.

b) Disconnect the two wires from the

coinbox switch terminals from inside
the metercase.

c) Squeeze the locking tabs on the top

and bottom of the switch body and push
the switch into the coinbox compart-
ment of the metercase.

P12 (COIN 2)

ADVANTECH



Control Board

P10 (COIN 1)

d) Remove the coindrop with its wire har-

ness from the unit.

Coindrop

Assembly

Top Locking Tab

Coinbox Switch Wires

Continued on the next page.

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды