Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 178

background image

3-1

PRODUCT OPERATION

ADVANTECH



Product flexibility allows a single

washer or dryer to accept multiple payment
systems over the life of the product. This elimi-
nates the need to purchase different SKUs
based on money acceptance requirements.

ADVANTECH



allows use of multiple money

acceptors, as well as Palm



and SMART Card

accountability systems at the same time. All
ADVANTECH



models come equipped with an

auxiliary communications port for connecting
SMART Cards, Ethernet boxes, Internet con-
trols, or additional devices. ADVANTECH



does

not require that purchasers be tied to an appli-
ance manufacturer’s proprietary card reader.
The ADVANTECH



open-architecture design

allows the use of a card system that best meets
the current business requirements to be in-
stalled into the product.

Whirlpool ADVANTECH



Commercial Laun-

dry Products allow the use of a Palm



handheld

device, also referred to as a “Personal Digital
Assistant” (PDA), for washer and dryer instal-
lation and setup. This includes setting special
vend-prices,  washer  and  dryer  software  up-
grades,  and  transferring  data  to  and  from  a
personal computer (PC). Information is set up
on  a  PC  using  ADVANTECH



Management

Software, which is then used to download
ADVANTECH



Handheld Software to the

Palm



. The Palm



uses an infrared light beam

to communicate information contained in the
Management Software to the washer and dryer.

ADVANTECH



SYSTEM OVERVIEW

Before downloading the Handheld Software to
the Palm



, Management Software must be

installed and running on the PC. Passwords,
machine setup, and Handheld Software are
available within the Management Software.
Detailed information about setup and installa-
tion of the ADVANTECH



Management Soft-

ware is available in the Software Service
Manual, Part

#8524743

. Additional

ADVANTECH



literature can be located in the

“Literature Cross-Reference Chart” on page
1-9.

Commands for the Management Software in-
stalled  on  the  PC  are  entered  by  using  the
keyboard  or  mouse.  Commands  for  the
Handheld Software are  entered into the Palm



by tapping the appropriate menu on its screen,
using a stylus that is provided with the handheld
device. Occasionally you may be asked to
enter text into the Palm



using the Graffiti



text

characters, or the Palm



keyboard. Additional

information regarding the use of Graffiti



text

and the Palm



keyboard can be found in the

Palm



Owner’s Manual.

«
...
55
56
57
58
59
...
»

Содержание ADVANTECH CAE2761K



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADVANTECH CAE2761K

Spacemaker DSKS333EC

Бренд: GE Страницы: 3

Бренд: Atag Страницы: 184

Бренд: Speed Queen Страницы: 12

Бренд: SNOWJOE Страницы: 20

YWNE52PP113TW01

Бренд: Alliance Laundry Systems Страницы: 50

Бренд: Ramteq Страницы: 20

Бренд: Swissh Страницы: 12

Бренд: MAKINEX Страницы: 47

Бренд: Lavorwash Страницы: 16

Бренд: Hallman Страницы: 20

Бренд: Kärcher Страницы: 196

Бренд: UNITED Страницы: 32

Бренд: Kärcher Страницы: 21

Бренд: Samsung Страницы: 56

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды