Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 69

Страница: 69 / 178

4-11

REMOVING THE PUMP, MOTOR START CAPACITOR, & MOTOR

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Unplug washer or disconnect power.

Remove the two T-20 Torx screws from
the bottom of the front panel.

To remove the front panel, pull the bottom
forward to release it from the two top
retaining clips, and remove the panel.

To remove the pump:

a) Release the two pump spring clips and

pull the pump away from the motor.

b) Place a container near the two pump

hoses to catch the water, then remove
the clamps from the inlet and outlet
hoses, and pull them off the pump.

Front Panel

T-20 Torx Screws

Pump Inlet Hose

Pump Outlet Hose

Release Spring Clips

Pump

Motor

REASSEMBLY NOTE:

Position the pump on

the motor shaft with the feet in the bracket
indents (circled below).

NOTE:

The pump, motor start capacitor, and

motor can more easily be accessed by tilting
the washer back, or by laying it on its rear
panel.

Motor Start

Capacitor

Retaining Clips

Continued on the next page.

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды