Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 108

Страница: 108 / 178

4-50

REMOVING THE BURNER ASSEMBLY,

FLAME SENSOR, AND HIGH-LIMIT THERMOSTAT

(GAS DRYERS ONLY)

To remove the burner assembly:

a) Remove the two hex-head screws from

the burner support bracket, and pull the
bracket away from the burner assembly.

Burner Assembly

Burner Support

Screws

b) Disconnect the following wires from the

burner assembly:

• Blue and white wires from the flame

sensor terminals.

• 2-wire connector from the ignitor.
• 2-wire and 3-wire connectors from

the coil assembly.

Flame Sensor
Wht & Blu Wires

Coil Assembly 2-Wire Connector

3-Wire Connector

Ignitor Connector

Remove the lower service access panel
(see step 4 on page 4-33 for the proce-
dure).

Unplug dryer(s) or disconnect power.

Turn off gas supply to dryer(s).

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды