Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 79

Страница: 79 / 178

4-21

To remove the base assembly:

a) Remove the tub ring, basket, outer tub,

and basket drive assembly (see steps
4 through 7 on pages 4-18 through 4-20
for the procedures).

b) Remove the skate plate (see step 2b).
c) Remove two 5/16

″

hex-head base as-

sembly screws from the rear panel.

d) Remove the rear panel from the base

assembly.

e) If you are replacing the base assem-

bly, remove the feet, springs, etc. from
the assembly.

NOTE:

The new base

assembly is supplied with suspension
pads already installed.

Base Assembly

Rear Panel Screw (1 of 2)

c) Pry the three suspension pads off the

top of the base assembly and replace
them (see the photo at the top of the
next column).

Suspension Pads

Pry Off

Suspension Pads

Skate Plate

REMOVING THE SUSPENSION SYSTEM & BASE ASSEMBLY

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Unplug washer or disconnect power.

To remove the skate plate and suspen-
sion pads:

a) Remove the tub ring, basket, and outer

tub (see steps 4 through 6 on pages
4-18 through 4-20 for the procedures).

b) Lift the skate plate off the base assembly.

(Shown With Lower Surface Facing Up)

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды