Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 40

Страница: 40 / 178

2-26

COINSLIDE INSTALLATION,
WASHERS & FREESTANDING
DRYERS

Check the electrical requirements. Make sure
that you are using the correct electrical supply,
and the recommended grounding method.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

Coinslide Into Metercase

7. Secure the coinslide to the metercase with

the coinslide mounting bolt.

Bolt

8. Replace the coinbox service access panel.

9. Reconnect electrical power.

10. Follow the appropriate procedure for either

manual or Palm



setup.

1. Unplug or disconnect electrical power.

2. Unlock and remove the coinbox service

access panel.

3. Unpack the coinslide and extension. If nec-

essary assemble the coinslide extension
onto the coinslide. Coinslides and exten-
sions are available from the manufacturers
of these devices.

4. Set the coinslide to the desired vend-price

using the instructions provided with the
coinslide.

5. With the coinslide still free, connect the two

harness wires to the coinslide switch, and
the green wire to the bottom of the exten-
sion.

6. Insert the coinslide into the metercase, and

attach the green ground wire to the meter-
case.

Wire Connectors

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды