Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 103

Страница: 103 / 178

4-45

REMOVING THE THERMAL FUSE, OPERATING

THERMOSTAT, DRIVE MOTOR, & BROKEN BELT SWITCH

Unplug dryer(s) or disconnect power.

Turn off gas supply to dryer(s).

Open the dryer door and remove the lint
filter screen, then close the door.

Remove the hex-head screw from the lint
duct bracket and remove the bracket.

Remove the two hex-head screws from
the lint duct and remove the duct.

Lint Filter Screen

Lint Duct Bracket & Screw

Continued on the next page.

Lint Duct Screws

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Thermal Fuse
(2 Screws)

Operating
Thermostat
(2 Screws)

2 Cover Screws

To remove the thermal fuse or operating
thermostat:

a) Remove the two wires from the termi-

nals.

b) Remove the two hex-head screws.

Blower Cover

Remove the two hex-head screws from
the bottom flange of the toe panel. Pull the
panel out at the bottom, pull down, and
remove the panel.

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды