Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 104

Страница: 104 / 178

4-46

To remove the drive motor:

a) Remove the wires from the thermal

fuse and operating thermostat termi-
nals (see the photo in step 7 on page
4-45).

b) Remove the two hex-head screws from

the blower cover and remove the cover.

c) Reach around to the back of the drive

motor and attach a 7/8

″

open-end

wrench over the hex-end of the motor
shaft, and a ratchet with a 1/2

″

drive on

the blower wheel hub.

d) Turn the blower wheel clockwise (shown

by the “REMOVE” arrow that is em-
bossed on the front of the wheel ) and
remove the wheel from the motor shaft.

e) Remove the three hex-head screws

from the blower housing and remove it.

Housing Screw
(1 of 3)

Blower Housing

f) Reach around behind the drive motor

and push the idler wheel arm to the left,
then remove the tension, and remove
the belt from the idler pulley.

Push To Left

Remove Belt
From Idler Pulley

REMOVE

TIGHTEN

7/8

″

Open-End

Wrench

Ratchet w/ 1/2

″

Drive

Blower Wheel

1/2

″

Drive

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды