Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 109

Страница: 109 / 178

4-51

c) Disconnect the gas line from the burner

manifold at the right rear corner of the
dryer.

d) Loosen the burner manifold clamp at

the inside back of the dryer.

e) Remove the two hex-head screws from

the burner mounting bracket, and pull
the burner assembly out of the unit.

Manifold Clamp Screw

Bracket Screws

To remove the ignitor

from the burner

assembly, loosen the 5/16

″

hex-head

screw, and remove the ignitor from the
mounting bracket.

Burner Assembly

Ignitor Screw

Bracket

Continued on the next page.

To remove the coils

from the burner

assembly, remove the two screws from
the bracket, and lift the two coils off the
cores.

Bracket Screws

Coils

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды