Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 130

Страница: 130 / 178

6-2

RUNNING THE MACHINE WITHOUT
A SMART CARD

1. Perform all steps under “Access Mode” on

page 6-1.

2. Push and release keypad position 3 (COLD).

3. The Washer is now ready for use as if

money or a SMART Card was used.

LED DISPLAY CODES

POSITION

MODE

FUNCTION

HOT

Hot water valve

ON/OFF

WARM

Cold water valve

ON/OFF

COLD

Agitation

ON/OFF

(water turns off)

MODEL

CAE2761K

First push – agitates
Second push – motor turns

OFF

MODEL

CAE2762K

First push – agitates at low speed
Second push – agitates at high speed
Third push – motor turns

OFF

NORMAL

Drain/spin operation (water turns off)

First push – drain (high speed spin only)
Second push – motor turns

OFF

Third push – spin (high speed spin only)
Fourth push – motor turns

OFF

GENTLE No action

(hidden

keypad)

Exit Service Routine

READ LIFETIME CYCLE COUNT

1. Perform all steps under “Access Mode” on

page 6-1.

2. Lifetime Cycle Count is displayed for about

one minute, then it goes back showing the
vend-price. Keypad #6 (hidden keypad)
can be pushed to exit this routine before the
one minute expires.

LED TEST ROUTINE

1. Perform all steps under “Access Mode” on

page 6-1.

2. Push and release keypad position 5

(GENTLE).

3. All LEDs light and the digits show “88888”.

4. Push and release keypad #6 (hidden key-

pad) to return to show cycle count.

5. Push keypad #6 (hidden keypad) a second

time to exit the test routine.

MANUAL OUT OF SERVICE (OFF)

This  procedure  allows  the  service  person  to
take  the  machine  out  of  service  for  needed
repairs.  The  display  shows  “OFF”  when  set.
The  display  shows  the  vend-price  when  put
back into service.

1. Perform all steps under “Access Mode” on

page 6-1.

2. Push and release keypad position 5

(GENTLE). All LEDs light and the digits
show “88888”.

3. Push and release keypad position 4 (NOR-

MAL). “Out” appears on the display a short
time to show the new status.

4. Push and release keypad #6 (hidden key-

pad) twice to exit. The word “OFF” now
replaces the vend-price.

5. To place the machine back into service,

perform steps 1 through 3 a second time.
The word “In” appears on the LED display
for a short time to show that the new status
took effect.

6. Press keypad #6 twice to exit the service

mode. The vend-price replaces the word
“OFF,” and the machine is now available for
customer use.

CODE

DESCRIPTION

Coinbox is removed.

Coinslide is pushed in.

Washer lid is closed.

Coindrop #2 receives
coin.
Coindrop #1 receives
coin.
Auxiliary (Smart Card) is
working properly.

SERVICE ROUTINE KEYPAD
FUNCTIONS

HOT

WARM

COLD

NORMAL

GENTLE

KEYPAD POSITIONS

NOTE:

Keypads #4, #5, and #6 are hidden on

single speed washers. Keypad #6 is hidden on
2-speed washers.

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды