Whirlpool ADVANTECH CAE2761K Скачать руководство пользователя страница 62

Страница: 62 / 178

4-4

c) If a mounting stud is not installed on

the new end cap, remove the stud from
the old cap, and install it on the new
one.

Left End

Cap

Mounting Stud

b) Remove the two hex-head screws from

the console support bracket, and slide
the end cap off the end of the panel.

Console Support
Bracket Screws

b) Remove the two screws from the card

reader assembly and remove the as-
sembly.

Card Reader Screws

Card Reader Assembly

To remove an end cap from the console:

a) Remove the hex-head screw from the

back of the end cap.

Back
Screw

Left End

Cap

Содержание ADVANTECH CAE2761K



















































































































































































Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды

Whirlpool ADVANTECH CAE2761K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ADVANTECH CAE2761K

Отзывы:

Похожие инструкции для ADVANTECH CAE2761K

Бренды по названию

Популярные бренды